Patton electronicメーカー1092ARCの使用説明書/サービス説明書
ページ先へ移動 of 20
USE R MANUA L MODEL 1092AR C High Speed, 2-Wire/4-Wire , Synchronous an d Asynchronous Rack Moun t Modem Card SALES OFFIC E (301)975-100 0 TECHNICAL SUPPOR T (301)975-100 7 http://ww w.
1.0 WARRANTY INFORM ATION Patton Electronic s warrants all Model 1092ARC components t o be free from defects, and wil l — at our optio n — repair or replace th e product should it fail within one year from the first date of shipment .
2.0 GENERAL INFORM ATIO N Thank you for your purchase of this Patton Electronics product . This product has been thoroughly inspected and tested and i s warranted for One Y ear parts and labor. If any questions arise durin g installation or use of this product, please contact P atton Electronics ’ T echnical Support at: (301) 975-1007 .
3.0 CONFIGUR ATIO N This section describes the hardware and software configuratio n switches and jumpers, and provides detailed instructions for all possibl e settings.
3.1.2 Configuration Switch Set “S1 ” The configuration switches on S1 allow you to specify the dat a rate, async/sync data format, transmit clock source and response t o RDL request.
Switch S1-8: Response to Remote Loo p Reques t Use Switch S1-8 to allow the Model 1092ARC to enter the Remot e Digital Loopback diagnostic test when requested to do so by the far en d modem. For example, when Switch S1-8 is set to “ON”, it will ente r RDL mode (See Section 5.
Switch S5-2: 2-Wire/4-Wir e Use Switch S5-2 to configure 2-Wire or 4-Wire operation . S5- 2 Settin g Descriptio n Of f 2-Wir e 2-Wire Operatio n O n 4-Wir e 4-Wire Operatio n Switch S5-3: Enable LAL and RDL from DT E Use Switch S5-3 to enable or disable the Local Analog Loopbac k and Remote Digital Loopback control from the DTE .
MAIN MENU Option 1: Display Active Configuratio n Select Option 1 to display the most recent configuration of the loca l Model 1092ARC (See below). The Model 1092ARC uses the activ e configuration for its operation. If you make changes to th e configuration, you must select MAIN MENU Option 8.
2. Data Forma t Select Option 2 in the SOFTWARE CONFIGUR A TIO N Menu t o select the sync data format (See below). 3. Clock Mod e Select Option 3 in the SOFTWARE CONFIGUR A TION Menu t o select the sync clock mode (See below) .
7. DTE Controlled Remote Digital Loo p Select Option 7 in the SOFTWARE CONFIGUR A TIO N Menu t o enable DTE control of the Remote Digital Loop Menu (See below). Th e Remote Digital Loop on the 1092ARC can be controlled from the DT E interface by selecting Enable (Option 1).
To run or terminate a particular test, key in the option to get to tha t screen menu. T est Mode options 2,3,7,8 and 9 require the 1092ARC to be in Dat a Mode with the remote 1092ARC. The Model 1092ARC Test Mode s are described below: OF F Terminates all test s 51 1 Initiates the built-in test pattern generator and detector .
3.3.1 Mode l 1001RCM12545 Rear Card Strap Setting s Figure 6 shows strap locations for the Model 1001RCM1254 5 (DB-25/RJ-45S) rear cards. These straps determine various groundin g characteristics for the terminal interface and twisted pair lines. JB3 an d JB4 are user configurable.
The table below provides an overview of interface strap function s for the rear interface cards. Following the table overview are detaile d descriptions of each strap’s function . DTE Shield (DB-15 Pin 1) & FRGND (JB3 ) In the connected position, this strap links DB-15 pin 1 & fram e ground.
4.0 INS TALLATIO N This section describes the functions of the Model 1001R14 rac k chassis, tells how to install front and rear Model 1092ARC Series card s into the chassis, and how to connect to the twisted pair interface an d the serial interface . 4.
4.3.2 Connect to a “DCE” Devic e Since the Model 1092ARC’s serial port is always wired as a DCE , you must use a null mode m cable when connecting to another DC E device such as a CSU/DSU, modem or multiplexer. This cable shoul d be of the shortest possible length that is appropriate to the interface yo u are using.
5.0 OPER ATIO N Once the Model 1092ARC is properly configured and installed, i t should operate transparentl y . This sections describes functions of th e LED status indicators, and the use of the built-in loopback test modes.
To perform an LLB test, follow these steps : 1 . Activate LLB. This may be done in one of three ways: - Move the front panel toggle switch to the right to “Local”. - Raise the LLB signal on the interface (see Appendix B). - Set Local Loop from the VT100 screen .
APPENDIX A PA TTON ELECTRONICS MODEL 1095R C FACTORY REPLACEMENT PART S AND ACCESSORIE S Patton Model # Descriptio n 1001RPEM-RA C ................ . 120/240V Rear Power Entry Modul e 1001RPSM-RU I .................. . 120/240V Front Power Supply Modul e 1001RPEM-RD C .
APPENDIX B (Continued ) PA TTON MODEL 1092ARC TERMINAL INTER FA CE PIN ASSIGNMEN T DB-25F Connector-DC E (RS-232 Interface ) Pin # Signa l 1...........................FG (Frame Ground ) 2.......................... TD ( T ransmit Data ) 3..............
3 8 APPENDIX D LINE INTER FA CE PIN ASSIGNMEN T (RJ45 Connector ) Pin Numbe r Signa l 1...................................................N/C (No Connection ) 2...................................................N/C (No Connection ) 3..................
デバイスPatton electronic 1092ARCの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 1092ARCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 1092ARCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 1092ARCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 1092ARCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 1092ARCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 1092ARCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 1092ARCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 1092ARCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。