Patton electronicメーカー2085の使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANUAL SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2085-D Doc# 047033U, Rev . E Revised 1/22/08 MODEL 2085 High Speed RS-232 to RS-485 Interface C.
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 2085 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container . This number may be obtained from Patton Electronics T echnical Service: (301) 975-1007, http://www .
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
3.0 CONFIGURA TION The Model 2085 is configured using an eight position DIP switch and a DCE/DTE switch. Figure 1 (below) shows the location of the DCE/DTE switch (externally accessible) on the PC board, as well as the power supply daughter board and terminal block.
3.1 SETTING THE DCE/DTE SWITCH For your convenience, the Model 2085 has an externally accessible DCE/DTE switch. If the device connected to the Model 2085 is a modem or multiplexer (or is wired like one), set the switch to “DTE”. This setting causes the Model 2085 to behave like Data T erminal Equipment and transmit data on pin 2.
4.1.3 4-WIRE CONNECTION USING TERMINAL BLOCKS If your RS-485 application requires you to connect two pairs of bare wires to the Model 2085, you will need to open the case to access the terminal blocks.
S1-4: Echo Mode The setting for switch S1-4 determines whether the Model 2085 echoes data back to the transmitting device (half-duplex mode only). S1-4 Setting On Echo On Off Echo Off S1-5: Carrier Control Method The setting for switch S1-5 determines whether the carrier is “Constantly On” or “Controlled by RTS”.
3.4 CONFIGURA TION SWITCH APPLICA TIONS The switch settings generally needed to configure the Model 2085 for various applications are shown in the table below . Note: Do not change switch settings until you have carefully read Section 3.3. 8 S1-1: “Xmt Off” Imp.
3.4 CONFIGURA TION SWITCH APPLICA TIONS The switch settings generally needed to configure the Model 2085 for various applications are shown in the table below . Note: Do not change switch settings until you have carefully read Section 3.3. 8 S1-1: “Xmt Off” Imp.
S1-4: Echo Mode The setting for switch S1-4 determines whether the Model 2085 echoes data back to the transmitting device (half-duplex mode only). S1-4 Setting On Echo On Off Echo Off S1-5: Carrier Control Method The setting for switch S1-5 determines whether the carrier is “Constantly On” or “Controlled by RTS”.
4.1.3 4-WIRE CONNECTION USING TERMINAL BLOCKS If your RS-485 application requires you to connect two pairs of bare wires to the Model 2085, you will need to open the case to access the terminal blocks.
3.1 SETTING THE DCE/DTE SWITCH For your convenience, the Model 2085 has an externally accessible DCE/DTE switch. If the device connected to the Model 2085 is a modem or multiplexer (or is wired like one), set the switch to “DTE”. This setting causes the Model 2085 to behave like Data T erminal Equipment and transmit data on pin 2.
3.0 CONFIGURA TION The Model 2085 is configured using an eight position DIP switch and a DCE/DTE switch. Figure 1 (below) shows the location of the DCE/DTE switch (externally accessible) on the PC board, as well as the power supply daughter board and terminal block.
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container . This number may be obtained from Patton Electronics T echnical Service: (301) 975-1007, http://www .
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 2085 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
APPENDIX B P A TTON MODEL 2085 RS-232 PIN CONFIGURA TIONS Copyright © Patton Electronics Company 1- (FG) Frame Ground 2- (TD) Transmit Data T o Model 2085 3- (RD) Receive Data From Model 2085 4- (RTS.
APPENDIX B P A TTON MODEL 2085 RS-232 PIN CONFIGURA TIONS Copyright © Patton Electronics Company 1- (FG) Frame Ground 2- (TD) Transmit Data T o Model 2085 3- (RD) Receive Data From Model 2085 4- (RTS.
USER MANUAL SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2085-D Doc# 047033UD, Rev . E Revised 1/22/08 MODEL 2085 High Speed RS-232 to RS-485 Interface .
デバイスPatton electronic 2085の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 2085をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 2085の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 2085の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 2085で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 2085を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 2085の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 2085に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 2085デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。