Patton electronicメーカー2172Rの使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANUAL MODEL 2172R Ruggedized 50-Mbps Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2172R-UM Doc# 03333U2-004 Rev .
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Compliance ................................................................................... 4 EMC Compliance:...............................
3 C Model 2172R Series Interface Pin Assignment ...................... 19 C.1 10/100Base-T Interface .............................................................. 19 RJ-45 ..............................................................................
4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 2172R components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment.
5 1.2 RADIO AND TV INTERFERENCE (FCC PART 15) This equipment generates and uses radio frequency energy , and if not installed and used properly—that is, in strict accordance with the manu- f acturer's instructions—may cause interf erence to radio and television reception.
6 1.5 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. • Mains Voltage: Ensure that the external power adapter is a listed Limited Power Source.
7 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor .
8 These units can automatically f orward LAN broadcasts , multicasts, and frames across a 2-wire v oice-grade twisted-pair link. The data is passed transparently (unmodified) through the 2172Rs or 2172s.
9 Figure 2. Model 2172R standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 2172R suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 6,000 ft (1.8 km) over 24 A WG (0.5 mm) twisted-pair wire.
10 1. T o function properly , the two Model 2172Rs m ust be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable .
11 3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The shielded RJ-45 por t labeled Ethernet is the A uto-MDIX10/100Base- T interf ace. This por t is designed to connect directly to a 10/100Base-T network. Figure 5 shows the signal/pin relationships on this interf ace.
12 4.0 CONFIGURATION The Model 2172R has eight DIP s witches f or configuring the unit for a wide variety of applications. This section descr ibes switch locations and e xplains the diff erent configurations.
13 Figure 7. DIP switch orientation 4.2 CONFIGURING DIP SWITCH S2 DIP s witch S2 is where you configure the CopperLINK line r ate, symmet- ric or asymmetr ic, Ethernet, and Ether net Shutdown. T able 1 summa- rizes def ault positions of DIP s witches S2-1 through S2-8.
14 Switch S2-1: Symmetric/Asymmetric Operation Use s witch S2-1 to configure the unit f or symmetric or asymmetric opera- tion.. Switches S2-2 and S2-3: Data Rate Use s witches S2-1, S2-2 and S2-3 to configure the CopperLINK line rates.
15 Switch S2-7: Ethernet Shutdown Use s witch S2-7 to enable or disab le Ether net Shutdown. When Ether net Shutdown is enab led, the 2172R will disable the Ether net interf ace when there is no CopperLINK link detected. When Ether net Shutdown is dis- abled, the Ethernet interface will alw ays be enab led.
16 5.2 FRONT PANEL LED STATUS MONITORS The Model 2172R f eatures three front panel LEDs that monitor power , the Ethernet signals, and the CopperLINK connection. Figure 8 shows the front panel location of each LED . T able 8 on page 16 describes the LED functions.
17 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T , IEEE 802.3 Ether net • CopperLINK Connection: RJ-45 or T erminal Block A.2 TRANSMISSION LINE T wo-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: 50 Mbps, symmetric upstream/downstream.
18 APPENDIX B MODEL 2172R SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2172R/EUI Ruggedized 50-.
19 APPENDIX C MODEL 2172R SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection T erminal Block Figure 1.
20 APPENDIX D DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note The actual distance and link performance ma y vary depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Cop yright © 2008 P atton Electronics Company All Rights Reser ved.
デバイスPatton electronic 2172Rの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 2172Rをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 2172Rの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 2172Rの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 2172Rで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 2172Rを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 2172Rの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 2172Rに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 2172Rデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。