Patton electronicsメーカー2155の使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANUAL MODEL 2155 CopperLink Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2155 Doc# 032111U Rev . A Re vised 2/12/03 An ISO-9001Cer tified Company.
2 CONTENTS 1.0 Warranty Information ................................................................. 3 1.1 Radio and TV Interference ............................................................ 3 1.2 CE Notice ........................................
3 1.0 W ARRANTY INFORMATION P atton Electronics warr ants all Model 2155 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment.
4 1.3 SERVICE All warr anty and non-warranty repairs m ust be retur ned freight prepaid and insured to P atton Electronics. All returns must hav e a Retur n Materi- als A uthorization number on the outside of the shipping container . This number ma y be obtained from P atton Electronics T echnical Ser vices at: • T el.
5 2.0 GENERAL INFORMATION Thank you purchasing this P atton Electronics product. This product has been thoroughly inspected and tested and is warr anted f or one year f or par ts and labor . If questions arise while installing or using this product, contact CopperLink T echnical Support at +1 (301) 975-1007 .
6 Figure 1. T ypical application The 2155/L and 2155/R work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application.
7 3.0 INSTALLATION Because the CopperLink Ether net Extender requires no configuration, it can be installed quickly . Installation consists of the f ollo wing: • Connect the line interf ace between the units (ref er to section 3.
8 1. T o function properly , two Ethernet Extenders must be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable .
9 cable . Figure 5 shows how to construct a cable to connect the 10Base-T interf ace to a 10Base-T Hub . Figure 5. Connecting the 10Base-T interf ace to a 10Base-T Hub 3.4 CONNECTING POWER An e xter nal A C or DC power supply is a vailab le separately .
10 External 48 VDC power suppl y • Input – Rated voltage: 36–60 VDC – Rated current: 0.25 A DC at nominal 48 VDC – 3-pin locking connector , 3.
11 4.0 OPERATION Once the CopperLink Ether net Extenders are properly installed, they should operate transparently . No user settings required. This section describes reading the LED status monitors.
12 T able 1: LED status monitor indications LED Description DSL Link (Activ e Green) Solid green (On) indicates that the end to end DSL F ramer Link is up , signifying that the link across the DSL span is activ e. The DSL Link LED is Off when the link is down.
13 4.2 T EST MODES The Model 2155 has a built-in proprietar y loopbac k test mode, plus a built-in V .52 BER test patter n generator , f or ev aluating the communica- tion link. These tests can be activ ated from the front panel of the Model 2155 Ether net Extenders .
14 APPENDIX A SPECIFICATIONS A.1 GENERAL CHARACTERISTICS • Compact low cost plug-and-pla y router • 10Base-T Ether net • Unlimited host suppor t • Six front panel LEDs indicate DSL & 10BT .
15 A.7 CONNECTORS RJ-45 on line side; shielded RJ-45 on Ether net por t A.8 POWER SUPPLY Exter nal 100–240 V A C , 50–60 Hz (univ ersal input option), +5 VDC out- put; 48 VDC (optional), 5 watts , +5 VDC output A.9 T EMPERATUR E RANGE 32–122°F (0–50°C) A.
16 APPENDIX B MODELS 2155 F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description 2155 Base Models 2155/L CopperLink Ether n.
17 APPENDIX C MODELS 2155 INTERF ACE PIN ASSIGNMENT C.1 10BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.
18 Notes ________________________________________________________ ________________________________________________________ ________________________________________________________ ____________________.
19 Notes ________________________________________________________ ________________________________________________________ ________________________________________________________ ____________________.
20 Notes ________________________________________________________ ________________________________________________________ ________________________________________________________ ____________________.
デバイスPatton electronics 2155の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronics 2155をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronics 2155の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronics 2155の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronics 2155で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronics 2155を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronics 2155の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronics 2155に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronics 2155デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。