Paxarメーカー6017の使用説明書/サービス説明書
ページ先へ移動 of 28
Monarch 6017 Han diP ri nt Prin ter TC60 17OI Rev . AB 4/01 ©20 00 M onarch Markin g System s, Inc. A ll righ ts reser ved.
Each produc t and pro gram c arries a r espective written wa rranty , the on ly war ranty on which the cu stomer can rely . Mona rch r eserve s the righ t to ma ke change s in the prod uct, the pr ograms, and their ava ilability at any tim e an d without n otice.
i TABLE OF CONTENTS GETTING STARTED ................................................. 1 - 1 Unpacking the Printer ............................................ 1 - 1 Programming Information ....................................... 1 - 1 Battery and Safety Information .
ii.
Getting Started 1 - 1 GETTING S TARTED Use these operating instructions with your Monarch 6017 HandiPrint Printer. The printer works with the SYMBOL SPT 17 00 or PPT 2700 handheld computer (“handheld”). The printer can print text, bar codes, and limited graphics on thermal direct receipt paper.
1 - 2 Getting Started Battery and Safety Information The printer is powered by a 7.4V Lithium Ion (LiIon) battery. There are no memory effects with LiIon batteries and reconditioning is not required. Lithium ion batte ries do not have to be completely drained before charging.
Getting Started 1 - 3 3. Open the strap at the VELCRO tab and pull the strap through the slot. You now have access to the battery door. Move the strap out of the way. 4. Unlock the battery door by sliding down the battery tab. 5. Open the battery door.
1 - 4 Getting Started 6. Insert the battery into the printer as shown. 7. Press the battery into place. 8. Lock the battery door by pushing up the battery tab. 9. Thread the strap through the slot and secu re the strap at the VELCRO tab. Make sure the strap is adjusted to fit your hand.
Getting Started 1 - 5 You can print while the battery is charging; howeve r, the battery may not receive a full charge. You can also charge the handheld while it is connected to the printer. However, the batteries (printer and handheld) may not receive a full charge.
1 - 6 Getting Started Reading the LED This table explains the LED indicator. LED Indicator Status Red On The charger is charging the battery at a fast rate. If the ba ttery voltage is below 5.0V, the battery is “trickle” charged until the battery reaches 5.
Getting Started 1 - 7 Connecting the Printer Attach the handheld to the prin ter's 14 - pin connector as shown. The handheld’s bottom lip fits snugly under the printer’s cutout.
1 - 8 Getting Started 3. Using the grommet provided, secure the strap into the attaching hole. 4. Thread the strap through the slot and secure the s trap at the VELCRO tab. Make sure the strap is adjusted to fit your hand. 5. Using the self - tapping Phillips screw provided, secure the button to the strap grommet.
Loading Supplies 2 - 1 LOADING SUPPLIES The printer can print text, bar codes, and some limited graphics on thermal direct receipt paper. See Appendix A, “Specifications” for the width and thickness requirements. 1. Open the supply cover by inserting your fingers into the rubber pull tab and pulling up firmly on the supply cover as shown.
2 - 2 Loading Supplies 2. Drop the supply into the well. Make sure the supply unwinds from t he top as shown. 3. Position the supply between the printhead guides. 4. Make sure some supply extends past the platen roller. 5. Close the supply cover. Tearing Supply The printer’s supply door acts as a tear bar.
Using the Printer 3 - 1 USING THE PRINTER This chapter includes information about printing, using the magnetic stripe reader, and scanning bar codes. Printing You must have a printing application installed on your handheld b efore you can print receipts.
3 - 2 Using the Printer Quickly swipe the card through the reader either left - to - right or right - to - left with the magnetic stripe in the reader. The magnetic stripe must be facing toward the handheld while it is passed through the reader. The green LED on the printer indicates the following: LED Indicator Status On Ready/waiting for card.
Using the Printer 3 - 3 Scanning Bar Codes Scanning bar codes is application specific. You should only scan a bar code when prompted by your application. 1. Point the scanner at a slight angle approximate ly four to eight inches from the bar code symbol.
3 - 4 Using the Printer Scanning Tips ♦ Make sure there are no voids in the bar code symbol. ♦ Hold the scanner four to eight inches from the bar code. Move the scanner toward and away from the bar code to find the correct distance for a successful scan.
Cleaning 4 - 1 CLEANING You may need to clean the printhe ad and platen roller after printing approximately six rolls of supply, whenever you load new supplies, or when you see voids in the print as shown. CAUTION Do not use sharp objects to clean the printhead.
4 - 2 Cleaning 4. Clean the platen roller with a dry cloth or small brush. You can also use another cotton swab moistened with isopropyl alcohol. Turn the platen roller with your finger and run the cotton swab or dry cloth across it. Make sure the platen roller is clean all the way around.
Troubleshooting 5 - 1 TROUBLESHOOTING If you cannot fix a problem, call Technical Support. Problem Action Does not feed or has a paper jam. Remove any jammed supplies. Reload supplies. Does not print. ♦ Check or replace the printer’s battery. ♦ Your handheld’ s application may include a query for the battery voltage.
5 - 2 Troubleshooting Problem Action Light /heavy printing or voids in printing. Clean the printhead. Check or recharge the battery. See “Charging the Battery” in Chapter 1 for more information. Your System Administrator may need to adjust the print contrast.
Specifications A - 1 SPECIFIC ATIONS Printer Specifications Height: 2.8 inches (71 mm) Width: 4.25 inches (108 mm) Length: 9.5 inches (241 mm) Weight: w/ battery & supply 1.
A - 2 Specifications Charging Time: Approximately 3 hours with no printing Communicatio ns: RS - 232 port Print Ratio 25% black maximum per square inch Supply Specifications Supplies: Thermal direct receipt paper Supply Thickness: 2.2 to 3.5 mils (receipt paper) Supply Width: 3.
Specificatio ns A - 3 Using the Optional Stand Read the following if you purchased the optional printer stand. The stand can be ♦ used on a table top or wall - mounted. ♦ adjusted to minimize glare on the handheld’s display ♦ folded flat for storage.
A - 4 Specifications For Wall - Mounting: Wall - mounting hardware is not included. Use two screws or nails that support at least 5 pounds (2.3 kg.). 1. Place the unfolded stand against the wall. 2. Use a pencil to mark inside the two keyholes for the screws or nails.
.
For supplies, service, or assistance call : 1-800-543-6650 (In the U.S.A.) 021 869 97 70 (In Switzerland) ww w .gomaro.ch.
デバイスPaxar 6017の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Paxar 6017をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPaxar 6017の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Paxar 6017の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Paxar 6017で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Paxar 6017を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPaxar 6017の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Paxar 6017に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPaxar 6017デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。