Paxarメーカー612の使用説明書/サービス説明書
ページ先へ移動 of 63
Users Manual 610 / 611 / 612 Printers PAXAR Systems Group Manual Edition 2.1 16 March 2001 Manual Part Number 441397.
This page left blank intentionally..
Users Manual - 610/611/612 Printers Contents • • i Contents Getting Started 1 Audience .............................................................................................................................. 2 Unpacking the Printer .........
ii • • Contents Users Manual - 610/611/612 Printers Lubricating the Knife ......................................................................................................... 43 Troubleshooting 44 Printing a Test Label .......................
Users Manual - 610/611/612 Printers Getting Started • • 1 Getting Started The Paxar 610 / 611 / 612 Care Label printers let you print text, graphics, and bar codes on thermal transfer (ribbon) fabric labels. This chapter includes information about ♦ Unpacking the printer.
2 • • Getting Started Users Manual - 610/611/612 Printers Audience The Operator's Handbook is for the person who prints and applies labels. Unpacking the Printer After you unpack the printer, you should have: a 610 / 611 / 612 printer, power cord, communication cable and a ribbon take-up core (may already be on take-up reel).
Users Manual - 610/611/612 Printers Getting Started • • 3 Establishing Communications Before the printer can accept print jobs from the host, you must: ♦ Connect the communication cable to the printer and to the host. ♦ Set the communication values on the printer to match those at the host.
4 • • Getting Started Users Manual - 610/611/612 Printers Default Printer Settings These defaults can be changed using Paxar's PCMate software. Print Speed - 4.0 ips (inches per second), Ribbon - High Energy, Supply Type - Black Mark, Contrast - 255, Backfeed - Enabled, Dispense Position - 120 dots, Backfeed Distance - 110 dots.
Users Manual - 610/611/612 Printers Getting Started • • 5 Button Functions Feed: Prints a label in the On-Demand mode. Feeds a blank label if there is no print job. Prints a label with error information that is useful to your System Administrator if an error is displayed.
6 • • Getting Started Users Manual - 610/611/612 Printers Setting Dip Switches To change the DIP switch settings, move the switches to the desired position and then turn on the printer. If you select Software Controlled, the parameters in Packet F will override the communication settings.
Users Manual - 610/611/612 Printers Getting Started • • 7 DIP Switches Upper DIP Switches 1 2 3 4 5 6 7 8 Baud Rate 38400 19200 9600 4800 2400 1200 Software Control ON ON OFF ON OFF ON ON OFF OFF .
8 • • Getting Started Users Manual - 610/611/612 Printers Lower DIP Switches 1 2 3 4 5 6 7 8 Flow Control XON/XOFF RTS/CTS DTR ON OFF OFF ON OFF OFF Diagnostics Normal Diagnostics Mode OFF ON Veri.
Users Manual - 610/611/612 Printers Loading Supplies • • 9 Loading Supplies This chapter describes how to load a roll of supply and a ribbon roll. You can use Paxar's fabric label kits containing fabric labels and ribbon. If you switch from black mark to continuous supplies make sure the DIP switches are set correctly.
10 • • Loading Supplies Users Manual - 610/611/612 Printers Loading Labels – 610 / 611 For instructions for loading labels for the 612, see page 15. Make sure the printer is configured for the correct supply type. To load a roll of labels: 1. Open the cover.
Users Manual - 610/611/612 Printers Loading Supplies • • 11 3. Lift printhead assembly using the printhead tab until the assembly locks into place.
12 • • Loading Supplies Users Manual - 610/611/612 Printers 6. Push down on the supply lever to unlock the supply guides. 7. Lay the label strip across the supply guide. Lift the auxiliary rollers slightly and thread the supply under the rollers until it appears in the knife opening.
Users Manual - 610/611/612 Printers Loading Supplies • • 13 9. Adjust the supply guides so they touch the supply. Push up on the supply lever to lock the supply guides into place. 10. Hold the printhead assembly by the printhead tab while pressing down on the printhead release.
14 • • Loading Supplies Users Manual - 610/611/612 Printers 12. Close the cover. 13. Press Feed to position the supply under the printhead. You may need to adjust the wide/narrow knobs depending on the width of your supply. See Chapter 4, "Care and Maintenance" for more information.
Users Manual - 610/611/612 Printers Loading Supplies • • 15 Loading Labels – 612 Make sure the printer is configured for the correct supply type. To load a roll of labels: 1. Open the cover. 2. Unlock the printhead by turning the retaining latch.
16 • • Loading Supplies Users Manual - 610/611/612 Printers 3. Lift printhead assembly using the printhead tab until the assembly locks into place.
Users Manual - 610/611/612 Printers Loading Supplies • • 17 IMPORTANT 6. Before threading the printer, you must set the label length adjustment. Turn the Label Length Adjustment Knob (A) so that the pointer on the turn bar is lined up with the black bar on the Label Length Gauge that corresponds to the length of the label to be printed .
18 • • Loading Supplies Users Manual - 610/611/612 Printers 7. Lay the label strip across the supply guide (B). It is not necessary at this point to put the label strip in the guide. Lay the label strip across the platen roller (C) and thread the end of the strip into the gap between the platen roller and the auxiliary feed (D).
Users Manual - 610/611/612 Printers Loading Supplies • • 19 9. Bring the label strip over the guide roller and across the platen roller to the left of the strip that is already around the roller. Place the end of the strip into the auxiliary feed and feed it through using the advance knob (G).
20 • • Loading Supplies Users Manual - 610/611/612 Printers Loading Ribbon To load ribbon: 1. Open the cover. 2. Unlock the printhead by turning the retaining latch. 3. Lift printhead assembly using the printhead tab until the assembly locks into place.
Users Manual - 610/611/612 Printers Loading Supplies • • 21 4. Push the deflector tab down. 5. Slide the extra ribbon core on the take-up reel as far as it will go with the writing on the end of the core facing out. Use your empty ribbon core as the take-up core.
22 • • Loading Supplies Users Manual - 610/611/612 Printers 7. Slide the ribbon onto the back reel as far as it will go with the writing on the end of the core facing out. The ribbon roll only fits on the reel one way. Carefully unwind a few inches of ribbon from the bottom of the roll.
Users Manual - 610/611/612 Printers Loading Supplies • • 23 10. Align the ribbon with the printhead and supply. CAUTION Make sure the ribbon is straight and centered throughout the path. 11. Rotate the take-up core until the leader is past the printhead.
24 • • Loading Supplies Users Manual - 610/611/612 Printers 14. Close the printhead by pressing down on the thumb well until you hear it click into place. Close the cover. Adjusting the Wide/Narrow Knobs You may need to adjust the two wide/narrow knobs according to the width of your supply.
Users Manual - 610/611/612 Printers Loading Supplies • • 25 For narrow supplies, turn the wide/narrow knobs counter-clockwise with a screwdriver until it pops back up.
26 • • Printing Users Manual - 610/611/612 Printers Printing ♦ This chapter explains how to - ♦ Use on-demand mode printing. ♦ Print an error label. ♦ Adjust the print positions. ♦ Print care symbols and special characters, such as the Euro-Dollar symbol.
Users Manual - 610/611/612 Printers Printing • • 27 Printer Alignment - Top and Bottom Copy – 612 The 612 printer must be adjusted so that the copy on the top and bottom of the label lines up correctly. On the base of the unit near the supply roll is an adjustment guide (see the picture on page 17).
28 • • Printing Users Manual - 610/611/612 Printers Non-Printing Zone A non-print zone is required for text (light copy) and bar codes (heavy copy). Thin lines and most fonts require a 0.25-inch non-print zone at the leading edge of the label. Bar codes, bold fonts, and Care symbol fonts require a 0.
Users Manual - 610/611/612 Printers Printing • • 29 Printing Serial Bar Codes Currently, the 610 / 611 / 612 printer does not support printing serial (ladder) bar codes. Parallel (Picket Fence) Bar Code Serial (Ladder) Bar Code Adjusting Print Positions You can adjust the supply, print, and margin positions by using the control panel buttons.
30 • • Printing Users Manual - 610/611/612 Printers Resend the format so these changes take effect. Change the settings after the batch is done printing. Review the following definitions for the different print position adjustments. Supply Position Adjusts the machine to print at the vertical 0,0 point on the supply.
Users Manual - 610/611/612 Printers Printing • • 31 Using the Knife The installed knife is two and a half (2-1/2) inches away from the printhead. Pressing and holding Feed for two seconds marks the tag under the printhead to be cut when it reaches the knife.
32 • • Printing Users Manual - 610/611/612 Printers Care Symbol Font Samples Ginetex Font The following table shows the characters available with Ginetex Font 70 and Font 71. Font 70 can fit five (5) symbols in 22mm (0.88 inches). Nafta Font The following table shows the characters available with Nafta Font 72 and Font 73.
Users Manual - 610/611/612 Printers Care and Maintenance • • 33 Care and Maintenance This chapter tells you how to ♦ Clear supply jams ♦ Clear knife jams ♦ Clean the printhead and platen rol.
34 • • Care and Maintenance Users Manual - 610/611/612 Printers Clearing Supply Jams When you are printing and a jam occurs, the Supplies light on the printer's front panel blinks. To clear the jam: 1. Turn off the printer. 2. Open the cover and printhead assembly.
Users Manual - 610/611/612 Printers Care and Maintenance • • 35 Cleaning The rate and frequency at which you print determines how often you must clean the printer.
36 • • Care and Maintenance Users Manual - 610/611/612 Printers 5. Moisten another cotton swab with isopropyl alcohol. Rub the cotton swab across the printhead and remove any build-up. 6. Rub the cotton swab across the supply sensor and remove any build-up.
Users Manual - 610/611/612 Printers Care and Maintenance • • 37 9. Close the exit cover by pushing firmly on it as shown. Both latches will click into place. 10. Close the cover and printhead assembly. 11. Turn on the printer. 12. Press Feed to position the supply under the printhead.
38 • • Care and Maintenance Users Manual - 610/611/612 Printers 3. Unlock the printhead by turning the retaining latch. 4. Press forward and down on the two latches on top of the printhead assembly as shown.
Users Manual - 610/611/612 Printers Care and Maintenance • • 39 6. Carefully unplug the cable from the printhead as shown. CAUTION The printhead is sensitive to static electricity, which can damage the printhead or reduce its life. Ground yourself by touching some metal, such as the printer's metal base, before touching the printhead.
40 • • Care and Maintenance Users Manual - 610/611/612 Printers 9. Snap the printhead into place. Make sure the printhead cable does not touch the ribbon roll. 10. Clean the new printhead with a cotton swab dipped in isopropyl alcohol to remove any salt or oil left from handling.
Users Manual - 610/611/612 Printers Care and Maintenance • • 41 Adjusting the Print Contrast You may need to adjust the print contrast if the printing is too light or too dark. Having the correct print contrast is important because it affects how well your bar codes scan and how long your printhead lasts.
42 • • Care and Maintenance Users Manual - 610/611/612 Printers Replacing the Fuse The printer is shipped with a 115-volt or 220 volt slo-blow fuse. To replace the fuse: 1. Disconnect the printer from the power source. 2. Use a screwdriver to pry open the fuse box in the back of the printer as shown.
Users Manual - 610/611/612 Printers Care and Maintenance • • 43 Lubricating the Knife We recommend lubricating the knife after using 15 rolls of supply or performing 100,000 cuts. To prevent excessive wear on the knife, regularly lubricate the knife cams.
44 • • Troubleshooting Users Manual - 610/611/612 Printers Troubleshooting This chapter provides ; ♦ Information about printing a test label. ♦ Solutions to minor printing problems. ♦ Explanations of error messages you may receive while using the printer.
Users Manual - 610/611/612 Printers Troubleshooting • • 45 Printing a Test Label To print test labels: NOTE: Do not print a test label on the 612 printer. Press Feed and Pause simultaneously. Hold for one second and release. Labels similar to these print: The first label shows the printer’s configuration by packer (A – G).
46 • • Troubleshooting Users Manual - 610/611/612 Printers Troubleshooting This section helps you correct some problems that may occur. Problem Action Error message appears during startup. Turn off the printer, wait fifteen seconds and then turn on the printer.
Users Manual - 610/611/612 Printers Troubleshooting • • 47 Error Messages You may receive the following types of error messages: ♦ Data Errors ♦ Communication Errors Some errors numbered 400 – 438 and 500 – 574 are internal software errors.
48 • • Troubleshooting Users Manual - 610/611/612 Printers 018 Code page selection defined in the field must be 0 (Internal), 1 (ANSI), 2 (DOS 437), or 3 (DOS 850). 020 Vertical magnification must be 1 to 7 . 021 Horizontal magnification must be 1 to 7 .
Users Manual - 610/611/612 Printers Troubleshooting • • 49 204 Source field must be 0 to 999 . 205 Copy type must be 1 (Copy after rules) or 2 (Copy before rules). 206 Increment / Decrement selection must be I (increment) or D (decrement). 207 Incrementing start position must be 0 to 2710 .
50 • • Troubleshooting Users Manual - 610/611/612 Printers 263 P rimary monetary symbol is invalid. 264 Secondary symbol selection must be 0 (none) or 1 (primary secondary sign). 265 Monetary decimal places must be 0 to 3 . 266 Character string length in Packet E must be 5 (MPCL control characters) or 7 (ENQ/IMD command character).
Users Manual - 610/611/612 Printers Troubleshooting • • 51 352 Insufficient font memory is available for the downloaded font. 380 Job request is outside the range 0 to 4 . 400 Invalid character following {. 401 Internal software failure. Call Technical Support.
52 • • Troubleshooting Users Manual - 610/611/612 Printers Communication Failures Errors 409 to 413 usually indicate a communication failure. These errors happen when the host and the printer cannot communicate. Ask your System Administrator for help.
Users Manual - 610/611/612 Printers Troubleshooting • • 53 Data Formatting Errors Errors 571 to 618 are data formatting errors. This type of error happens when a field prints incorrectly. Your System Administrator can correct the format, batch, or graphic packet and send the print job again.
54 • • Troubleshooting Users Manual - 610/611/612 Printers Machine Faults Errors 700 to 765 happen when there is a problem with the printer. Error Description/Action 700 An error is pending and the printer cannot continue with the batch. 701 Printer received a comman d that it cannot execute while it is running.
Users Manual - 610/611/612 Printers Troubleshooting • • 55 768 Printhead has more than 10 bad dots or is not connected. Make sure the printhead is connected and if necessary, replace the printhead. 770 The print motor is not ready. Call Technical Support.
56 • • Appendix A - Specifications & Accessories Users Manual - 610/611/612 Printers Appendix A - Specifications & Accessories Printer Specifications Height: 12.5 inches (318 mm) Width: 12 inches (305 mm) Depth: 13 inches (330 mm) Weight: 29 lb.
Users Manual - 610/611/612 Printers Appendix A - Specifications & Accessories • • 57 Supply Specifications Supply Types: Thermal Transfer Perforated Fabric Labels Fabric Label Kits: Kits include fabric and ribbon Paxar Systems: The fabric is available in standard widths, ranging from 1.
58 • • Appendix A - Specifications & Accessories Users Manual - 610/611/612 Printers Ribbon Specifications Ribbon Storage: Do not leave ribbon in direct sunlight, high temperatures, or high humidity. Ribbon Type: CT1111 (Paxar Systems) Ribbon Widths: CT1111 is available in the following widths: 1.
Users Manual - 610/611/612 Printers Contacting Paxar • • 59 Accessories ♦ International Fonts ♦ Internal TwinAx/CoAx Protocol Convertor ♦ LAN Print Server RJ-45 Connector (10BaseT) BNC Conne.
デバイスPaxar 612の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Paxar 612をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPaxar 612の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Paxar 612の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Paxar 612で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Paxar 612を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPaxar 612の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Paxar 612に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPaxar 612デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。