PaxarメーカーMonarch 9476の使用説明書/サービス説明書
ページ先へ移動 of 64
TC9476OI Rev. AA 4/99 © 1995 Monarch Marking S ystem s , Inc. All rights reserved. Assembly and Setup Instructions Monarch TM 9476 TM Mobile Printing Station.
Each product and program carries a respective written warrant y , the only warranty on which the customer can rel y . Monarch reserves the right to make changes in the product, the programs, and their availability at any time and without notice.
Preface The Monarch 9476 Mobile Printing Station, or "the Station," allows you to mobilize and use up to four Monarch ® 9490 printers. The 12-volt battery stored in the Station powers the printers. A portable data collection device or portable PC sends the data to the printers through a single, shared communication cable.
Other Documentation ---------------------------------- -------------------------------------------- T o send data to the printers and print labels or tags, see the following additional manuals: T o: S.
Table of Contents Chapter 1. Assembling the Station . . . . . . . . . . . . . . . . . . . . . . 1-1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 T ools You Need . . . . . . . . . . . . . . . . . . . . . .
Chapter 4. T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Changing Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1. Assembling the Station This chapter describes how to assemble the Station and install the batter y , battery charge r , printers, and optional items. Parts List -------------------------------------- -------------------------------------------- ------------------ Make sure you received the listed quantity of the following parts.
Package #2: Inside Cart: F (2) 8-32 nuts/ lockwashers (black) F (1) green wire (inside cart) F (2) 8-32 x 1/2" slotted screws (black) F (1) host input cable (encased in cable tube) F (1) cord bra.
T ools You Need ------------ -------------------------------------------- ------------------------------------ T o assemble the Station, you need: F flathead (common) screwdriver F Phillips screwdrive.
3. On a firm surface, using a piece of cardboard for a pad, stand the axle on one end. Hammer an end cap onto the axle. The end cap should lock firml y . 4. Slide the following parts, in this orde r , onto the axle: one wheel, one washe r , and two axle mounts.
5. At the rear of the Station (end closest to the side where the cabinet door opens), push the two axle mounts firmly into the sockets of the rear legs. (Figure 2.) Hold onto the uncapped end of the axle so the axle assembly stays togethe r . 6. Place the other end cap onto the uncapped end of the axle.
Step 2: Adjusting the Station’s Height ------------------------------------ -------------- 1. Remove the following items from their packaging: F (4) 1/4"-20 x 3/4" bolts (black) F (4) 1/4"-20 wing nuts (black) F (1) plastic cable-tube clamp (may already be attached to the cable tube) 2.
n Do Not set the top shelf to the highest adjustment. 5. Attach the plastic cable-tube clamp around the bottom of the cable tube as shown (if it is not already attached). Squeeze the finger grips to lock the clamp around the cable tube. Use pliers to secure the cable clamp tightl y .
2. Open the Station’s cabinet. Press the chrome handle insert into the cabinet door and fasten it with two 5/8" phillips screws. (Figure 4.) 3. Position the cord bracket over the mounting holes on the lower shel f ’s edge shown. Fasten the bracket with two 1/2" slotted screws and 8-32 nuts/lockwashers.
Attach the Push Handle 1. Remove the following items from their packaging: F (1) push handle F (4) 1/4"-20 x 3/4" hex bolts F (4) 1/4"-20 nuts F (4) 1/4"-20 washers 2. Attach the push handle to the front or rear of the Station using four 3/4" hex bolts, 1/4"-20 washers, and 1/4"-20 nuts as shown.
Attach the Drop Shelf 1. Remove the following items from their packaging: F (1) support brace F (1) metal rod F (1) drop shelf F (2) end caps F (2) 1/4"-20 x 1/2" phillips screws F (2) plastic washers 2.
3. Slide the metal rod into the hole in the Station’s corner support and through the support brace until the rod exits through the hole in the other corner support. Y ou may have to reach under the support brace to guide the rod into the opposite hole.
9. Slide the metal rod through the slot in the side of the drop shelf and into the hole in the Station’s corner support. Push the rod until it exits through the hole in the other corner support. Y ou may have to reach under the support brace to guide the rod into the opposite hole.
Attach the Data Ent ry T erminal Cradle The data entry terminal cradle is shipped fully assembled. T o attach it, place it as shown on any of the Station’s shelves. The magnets on the cradle anchor it to the Station. (Figure 9.) Figure 9 T erminal Cradle Magnet Chapter 1.
Step 5: Installing the Batte ry and Charger ------------------------------------------ Follow the steps below to install the battery and battery charge r . Install the Batte ry w Only qualified service personnel may install or replace the batter y . 1.
2. Find the two holes in the floor toward the back of the cabinet. Insert a retainer rod’s short end (end without the threads) into one of the two holes as shown. Tilt the long end of the retainer rod up until it slides down through the hole. Repeat the process with the other retainer rod in the other hole.
3. Place the battery on the cabinet floo r . Remove the cardboard packaging. Use a 15mm bolt, washe r , lockwashe r , and M5 nut to attach the white battery wire to the positive (+) battery post. (Figure 11.) 4. Slide the battery to the back of the cabinet.
7. Place the rubber bracket across the top of the batter y . Use 1/4"-20 wing nuts, washers, and lockwashers to attach the retainer rods to the rubber bracket. Tighten both wing nuts equally to secure the batter y . (Figure 12.) Figure 12 Ground Wire Rubber Bracket Retainer Rod Chapter 1.
Install the Batte ry Charger 1. Remove the following items from their packaging: F (1) battery charger F (2) metal retainer rods F (1) rubber bracket F (2) 1/4"-20 wing nuts F (2) 1/4"-20 wa.
2. Find the two holes in the floor toward the front of the cabinet. Insert a retainer rod’s short end (end without the threads) into one of the two holes as shown. Tilt the long end of the retainer rod up until it slides down through the hole. Repeat the process with the other retainer rod in the other hole.
3. Insert the power cord (packaged with the battery charger) into the power socket on the back of the charge r . (Figure 14.) 4. Insert the battery cable into the battery socket on the back of the charge r . (Figure 14.) The cable is keyed. 5. Make sure the voltage selector switch on the back of the charger is set correctly (115V in U.
7. Position the charger between the retainer rods so the back of the charger rests against the metal L -bracket. The status lights on the front of the charger should face out.
10. Plug the heavy-duty power cord into the external power socket on the outside panel of the Station. (Figure 15.) n Do Not plug the external power cord into a wall outlet until you are ready to charge the batter y . See "Charging the Battery" for important battery information.
2. Position the printer bracket on the top shelf of the Station, facing one of the Station’s fan-fold slots as shown. Align the holes in the printer bracket with the holes in the shelf and fasten with 8mm screws and M4 nuts. (Figure 16.) n All printer brackets must face the same direction.
1. Insert two M3.5 washers and two 10mm shoulder screws into the sides of the printer as shown and tighten with a screwdrive r . (Figure 17.) 2. The power packs for the printers are attached to the Station’s top shelf. Insert the tabs on the power pack into the slots of the battery well in the base of the printe r .
3. Slide the printer into the printer bracket so the printer faces the fan-fold slot in the Station’s top shelf. The printer’s shoulder screws slide into the vertical slots in the printer brackets. Make sure the back of the printer rests against the upturned metal ledge on the printer bracket.
4. The communication cables for the printers are located inside the Station’s cable tube. Insert the communication cable into the printer port as shown.
Chapter 2. Loading Supplies The Station can accommodate fan-fold printers or roll-fed printers. Fan-fold printers can also print roll supplies. This section describes how to load both types of supplies. See your 9490 Operator’s Handbook to load roll supplies in roll-fed printers.
2. Pull the supply guide forward and down as shown. (Figure 22.) 3. Tip the printhead assembly up and over the platen roller as shown. (Figure 23.) Figure 22 Supply Guide Figure 23 Printhead Assembly .
4. Slide the latches on the back of the printer toward the cente r . (Figure 24.) 5. Continue to push the printhead assembly toward the rear of the printer until it opens completel y .
2. Center a strip of supply over the supply deflecto r . The supply deflector’s rubber O-rings must be positioned inside the edges of the suppl y . (Figure 25.) If you do not need to adjust the position of the O-rings, skip to step 6. 3. Lift one end of the supply deflector to remove it from the supply well.
6. Fan all four sides of the supply stack and straighten any curved or bent corners. This will prevent supplies from sticking together and causing feed jams. 7. Place the supply stack on the bottom shelf, directly beneath one of the Station’s fan-fold slots.
9. Feed the supply’s leading edge into the printer’s fan-fold slot. The black mark on the supply must be facing up; if it is not, flip the supply stack ove r . Make sure the arrow printed on the back of the supply points toward the printe r . Center the supply in the printer by lining up the black mark within the centering notch.
11. Continue feeding the supply strip through the fan-fold slot until the strip exits through the back of the printe r , under the supply deflecto r . The supply strip should feed around the supply deflector and over the top of the printer as shown. (Figure 28.
12. Feed the supply strip through the upper opening in the supply guide. (Figure 29.) 13. T o close the printe r , push the top assembly toward the printe r , close the supply guide, and latch the faceplate into place.
Loading Roll Supplies in Fan-Fold Printers ---------------------------------- -------- T o load roll supplies into your fan-fold printe r , follow the steps belo w . 1. Open the printe r . 2. Lift one end of the supply deflector to remove it from the supply well.
3. Squeeze the tabs and adjust both supply holders to the width of your suppl y . (Figure 31.) n Make sure the arrow at the end of the each supply holder points to the correct width.
4. Insert the roll of supplies between the supply holders inside the printer and press until the supply roll snaps into place. The supply roll should unwind as shown. (Figure 32.) n Make sure the supplies turn freely in the supply well. Figure 32 Supply Holder Chapter 2.
5. For non-peel mode printing, feed the supply strip through the upper opening in the supply guide. (Figure 33.) Figure 33 Supply Guide Upper Opening 9476 Assembly and Setup Instructions 2-12.
6. On-demand printing only: For peel mode printing, feed the supply strip through the lower opening in the supply guide. (Figure 34.) When you print, labels peel automatically through the top opening in the label guide and the backing paper exits out the bottom opening.
Loading Ribbon -------------------------- -------------------------------------------- ------------------ Use ribbon when printing on thermal transfer supplies. T o load the ribbon cassette into the printer: 1. Open the printer and remove the ribbon cassette.
Reloading a Ribbon Cassette -------- -------------------------------------------- -------------- T o reload your ribbon cassette, remove the ribbon cassette from the printer and follow these steps: 1. Locate the end of the cassette with the two latches.
4. Remove the used ribbon and take-up reel and discard. Open a package of new ribbon. n Do Not wrinkle or crush the ribbon. 5. With the ridged end of the take-up reel facing down, place the ribbon roll on the spool with the foam washer (on the half of the cassette with the latches).
Printing -------------------- -------------------------------------------- ---------------------------------------- T o print supplies from the printers on the Station, follow the steps belo w . See Addressing a Monarch 9490 Printer for instructions on setting up your data collection application to send commands to specific printers on the Station.
3. T urn each printer on and press each printer’s trigger to calibrate the suppl y . You are now ready to collect data and print. n T o conserve the batter y , make sure the Station’s power switch is turned off when not in use.
Chapter 3. Charging the Battery The Station’s battery charger is a fully automatic, maintenance-free charge r . You must charge the battery before using the printers on the Station. T o charge the batter y , plug the Station’s AC power cord into a grounded outlet.
Important Charging Info rmation ---------------------------------- ------------------------ w DANGER! RISK OF ELECTRICAL AND FIRE HAZARD. CER TAIN ACTIONS M AY RESU LT IN DE ATH, SERIOUS INJUR Y , SHOCK, OR BURNS. F Do Not disassemble the battery charger; take it to an authorized repair center for repair or service.
Batte ry Life ---------------------------------------------- -------------------------------------------- ------ If you leave the battery charger plugged in and constantly charging when the Station is not in use, the battery life is maximized for the application.
9476 Assembly and Setup Instructions 3-4.
Chapter 4. Troubleshooting This chapter describes how to solve some common problems, as well as how to change the two fuses on the Station. Solving Problems -------------------------------------------.
Changing Fuses ---------------------------------- -------------------------------------------- ------------ There are two fuses for the Station: one connected to the battery (battery fuse), and one connected to the external power socket (AC fuse). The power switch on the front of the Station must be off while changing fuses.
2. Open the Station’s cabinet. Press and turn the fuse cover as shown until it pops out. (Figure 41.) 3. Pull the fuse out of the cove r . (Figure 41.) 4. Insert a 15 A, 32 V , slow blow fuse (size 3AG) into the fuse cover until the fuse is fully seated.
Changing the AC Fuse 1. T urn the Station’s power supply off and unplug the power cord. (Figure 43.) 2. Unplug the other end of the power cord from the Station. 3. Use a flathead screwdriver to carefully pry open the fuse cover (located under the power socket on the front of the Station).
4. Slide the fuse holder out and remove the fuse. (Figure 44.) 5. Insert a 250VAC, 6.3-amp, slow blow fuse into the fuse holder until the fuse snaps into place. (Figure 44.) 6. Push the fuse holder until it snaps back into place. (Figure 44.) 7. Plug the power cord back into the power socket on the Station.
9476 Assembly and Setup Instructions 4-6.
Chapter 5. Specifications This chapter describes the Station’s physical characteristics. See your 9490 Operator’s Handbook for printer specifications. Utility Cart -- -------------------------------------------- -------------------------------------------- ------ Height 42 inches (106.
F Cycle Use: 100% depth of discharge approx. 250 cycles 50% depth of discharge approx. 550 cycles 30% depth of discharge approx. 1200 cycles Cycle Life is approximate and many factors effect an individual battery’s performance.
.
For supplies, service, or assistance call: TOLL FREE: 1-800-543-6650 (In the U.S.A.) 1-800-263-4650 (In Canada) www.monarch.com Published by the Technical Communications Department.
デバイスPaxar Monarch 9476の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Paxar Monarch 9476をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPaxar Monarch 9476の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Paxar Monarch 9476の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Paxar Monarch 9476で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Paxar Monarch 9476を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPaxar Monarch 9476の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Paxar Monarch 9476に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPaxar Monarch 9476デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
