Pelcoメーカー90の使用説明書/サービス説明書
ページ先へ移動 of 24
INST ALLA TION 090 Series Camclosure ® Indoor Integrated Camera System C2462M-D (3/08) Surface Mount/In-Ceiling.
.
C2462M-D (3/08) 3 Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C2462M-D (3/08) List of Illustrations 1 How to Remove the Dome Bubble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 Ceiling/W all In stallation . . . . . . . . . . . . . . . . . . . . . .
C2462M-D (3/08) 5 Important Safety Instructions 1. Installation and servicing should be d one only by qualified se rvice personnel and conform to all local codes.
6 C2462M-D (3/08) Description The ICS090 Series Camclosure ® integrated camera system integrates a camera and lens package in a small, discreet dome. The system is easy to install and can be mounted or recessed to the surface of a ceiling or wall.
C2462M-D (3/08) 7 Remove the Dome Bubble T urn the dome bubble counterclockwise and lift (refer to Figure 1). Place the b ubble on a nonabrasive surface. If the unit is supplied with a dome liner , remove the li ner b efore installing the un it. T o re move the liner , gently lift it from the unit.
8 C2462M-D (3/08) Install the Back Box The installation methods for the ICS090 Series include the following options: • Mount to the surface of a ceiling or wall • Install in a suspended ceiling .
C2462M-D (3/08) 9 4. Use the 6-32 toggle bolts (not supplied) to at tach the surfa ce mount ring and back box to the mounting surface, refer to Figure 2. NOTE: For a concrete ceiling/wall installation, use 8-32 mounting hardware (not suppl ie d), refer to Figure 3.
10 C2462M-D (3/08) IN-CEILING INSTALLATION: SUSPENDED CEILING Refer to Figure 4 and complete the following steps. 1. Remove the ceiling tile from the ceiling. 2. Cut a 4-inch diameter h ole in the ceiling tile. 3. Remove the surface mount ring from the back box.
C2462M-D (3/08) 11 Figure 5. How to Remove Surfac e Mount Ring from Back Box AC operation only: If you are wiring more than one ICS090 Camclosure to the same transformer , connect one side of the transformer to the red wire on all units, and then connect the other side of the transformer to the black wire on all units.
12 C2462M-D (3/08) IN-CEILING INSTALLATION: FIXED CEILING/W ALL Refer to Figure 6 and complete the following steps. 1. Cut a 4-inch diameter h ole in the ceiling/wall. 2. Remove the surface mount ring from the back box. Refer to Figure 5 and complete the following steps: a.
C2462M-D (3/08) 13 INSTALLATION TO THE SURF ACE OF A 4S STANDARD ELECTRICAL BOX Refer to Figure 7 and complete the following steps. 1. Attach the adapter ring to the 4S box with the two 8-32 x 1.00-inch screws (s upplied). 2. Connect the video cable/wires.
14 C2462M-D (3/08) INSTALLATION IN A 4S DEEP ELECTRICAL BOX Refer to Figure 8 and complete the following steps. 1. Remove the surface mount ring from the back box. Refer to Figure 5 and complete the following steps: a. Place your fingers on the circular marks loca ted on the sides of the surface mount ring.
C2462M-D (3/08) 15 Camera Positioning Manually rotate and tilt th e camera module to positio n the camera. Do not over- rotate the module. Figure 9. Positioning the Camera WAR NI NG : Excessively turning the module in one direct ion could result in damage to the wiring.
16 C2462M-D (3/08) Camera Adjustments SWITCH SETTINGS SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to the switch drawing. The switch is located n ext to the lens.
C2462M-D (3/08) 17 V ERTICAL PHASE ADJUSTMENT (24 V AC OPERATION ONLY) When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. T o elim inate vertical roll, reverse the 24 V AC connections on one camera.
18 C2462M-D (3/08) Reinstall the Dome Bubble DOME LINER INSTALLATION If the unit is supplied with a dome liner , reinsta ll t he liner before installing the dome bubb le. T o install the liner , refer to Figure 11 comp lete the following steps: 1. Align the studs located on the camera module with the clips on the liner .
C2462M-D (3/08) 19 DOME BUBBLE INSTALLATION T o insta ll the dome bubble refer t o Figure 12 and complete the fo llowing steps: 1. Select the bubble (clear or smoked). 2. Align the standoffs of the bubble with the slots of the back box. 3. T urn the bubble clockwise, until it locks in place.
20 C2462M-D (3/08) Service Connector An optional 4-foot service/monitor cable, part numb er ICS090-SC, is available for on- site setup and adjustments. T o use the cable simply plug one end of the cable directly into the service connector of the ICS090, and then connect the other end to any st andard BNC (VIDEO IN) connector on a monitor .
C2462M-D (3/08) 21 Specifications BACKBOX Electrical Input V oltage 12 VDC or 24 V AC (±10%), autosensing Power Consumption 3 W or less Video Connector BNC General Pan/T ilt Adjustment Pan 360° T il.
22 C2462M-D (3/08) The materials used in the manufacture of this document an d its components are compliant to th e requirements of Directiv e 2002/95/EC.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, witho ut charge, any mer c handise proved defective in ma terial or wo rkmanship for a period of one year after th e date of shipment.
Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
デバイスPelco 90の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco 90をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco 90の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco 90の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco 90で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco 90を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco 90の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco 90に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco 90デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。