PelcoメーカーC1302M-F (11/08)の使用説明書/サービス説明書
ページ先へ移動 of 24
INSTALLATION C1302M-F (11/08) ExSite ® Series Explosionproof Pan and T ilt Sy stem.
2 C1302M-F (11/08).
C1302M-F (11/08) 3 Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Getting Started .
4 C1302M-F (11/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed al l warnings. 4. Follow all instructions. 5. Do not bl ock any ven tilation openings. Ins tall in accordance with the manu facturer’ s instructions.
C1302M-F (11/08 ) 5 Getting Started Thank you for purcha sing Pelco’ s ExSite ® Series explosionproof integrated positioning system. This manual i ncl udes instructions for installing all the componen ts of the E xSite Series sy stem.
6 C1302M-F (11/08) Install the Power Module Attach the power module to the mo unting surface. Use only insta llation methods and materials capa ble of supporting fou r times t he maximum specified load o f the system (220 lb /100 kg).
C1302M-F (11/08 ) 7 CONNECT WIRING Refer to the following informa tion to connect the wires an d cables as required. NOTES: • Relay 3 is allocated specific ally for an external washer (not supp lied by Pelco ). • All relays ar e specified fo r 32 VDC, 0.
8 C1302M-F (11/08) DIP SWITCH SETTINGS Configure the receiver address, termination, and baud se tting for the system. The DIP switches to configure th ese settings are located on the to p of the power module. NOTE: No DIP switch settings are re quired for Coaxitron contr ol.
C1302M-F (11/08 ) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF O FF OFF OFF 2 ON OFF OFF OFF OFF OFF OF F OFF 3 OFF ON OFF OFF OFF OFF OF F OFF 4 ON O.
10 C1302M-F (11/08) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OF F OFF ON ON OFF OF F 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF O.
C1302M-F (11/08 ) 11 T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OF F OFF ON 144 OFF OFF OFF OFF ON OFF.
12 C1302M-F (11/08) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 2 3 9 O NO NO NO N O F F O NO NO N 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON .
C1302M-F (11/08 ) 13 Install the Camera Module T o install the camera mo dule do t he following: 1. Refer to Figure 4. Loosen the set screw at the ba ck of the enclosure with the provided 1.5 mm Alle n wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanne r wrench to loosen the ba ck of the camera enclosur e (refer to Figure 5).
14 C1302M-F (11/08) 3. Slide th e camera modul e into the enclosure. Ref er to Figur e 6 to posi tion the camera module pr operly in the enclosure . Careful ly mate the camera’ s po wer connector to the ma ting connector locat ed inside the enclosur e.
C1302M-F (11/08 ) 15 4. Refer to Figure 8 and do the following to install the arm of the wiper: a. Place the su pplied gree n bushing on the stud l ocated be hind the ha ndle of the camera module . The bushin g should be in the sam e orientatio n as shown in Figure 8.
16 C1302M-F (11/08) Install the Pan and T ilt Unit 1. Check fo r proper se ating of t he power modu le seal. Make sure the se al is fully seated in t he groove o n the top of the powe r m odule. Figure 9. Factory-Installed Power Module Seal 2. Refer to Figure 10 an d attach t he pan and tilt unit to the power mo dule.
C1302M-F (11/08 ) 17 Install the Sun Shroud 1. Place the supplied nylon washer s on the 6-32 Phillips pan head screws. Refer to Figure 11. 2. Align the moun ting holes of the sun shrou d with the holes on top o f the enclosure. 3. Use the su pplied nyl on washers an d screws to se cure the su n shroud to the enclosu re.
18 C1302M-F (11/08) Maintenance CAMERA MODULE REPLACEMENT T o replace t he camera mod ule do th e following: 1. Remove the back cap of the came ra enclosure. Refer to Figur e 12 and do the following: a. Loosen the set screw with a 1 .5 mm Allen wren ch.
C1302M-F (11/08 ) 19 3. For mo dels with wiper s, also re move the wiper a rm and the g reen bus hing from th e unit (see F igure 13) . 4. Slide the camera module out of the enclosure. 5. Install the new camera mo dule by doin g the follo wing: Slide the camera module into the enclo sure.
20 C1302M-F (11/08) 6. Refer to Figure 13 an d do the foll owing to r einstall the ar m of the wipe r: a. Reinstall the gree n bushing on the stud locate d behind the handle of the camera module. b. Reinstall the wiper arm. Pl ace the ridg e of the a rm in the n otch of th e enclosure tab and the slot of th e arm ov er the gre en bushing.
C1302M-F (11/08 ) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input V olt age Range ±10% Power Consumptio n Maximum 60 W (120 VA) per system Electrical Connections 6-foot wire harness with c onnections for power , video, da ta control, alarm inputs , and auxiliary outputs MECHANICAL Cable Entry One 0.
22 C1302M-F (11/08) *Manual control of camera setup functio ns can be done with CM6700, CM 6800, CM8500, CM 9500, CM9740 , CM9760, CM9770, CM9780, KBD200A , KBD300A, and MPT 9500 control lers, but not with CM75 00, MPT9000, o r KBD9000 contr ollers.
The materials used in the manufacture of this documen t and it s components are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains elec trical or electronic components tha.
Pelco, Inc. Worldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .
デバイスPelco C1302M-F (11/08)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Pelco C1302M-F (11/08)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C1302M-F (11/08)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C1302M-F (11/08)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C1302M-F (11/08)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C1302M-F (11/08)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C1302M-F (11/08)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C1302M-F (11/08)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C1302M-F (11/08)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
