Pelcoメーカーc1405M-Eの使用説明書/サービス説明書
ページ先へ移動 of 16
EH4700 Series Envir onmental Enclosur es Installation/ Operation Manual C1405M-E (11/03) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.
2 Pelco Manual C1405M-E (1 1/03) CONTENTS Section Page GENERAL....... ................................................................................................... 3 IMPORT ANT SAFEGUARDS AND WARNINGS ....................................... 3 DESCRIPTION .
Pelco Manual C1405M-E (1 1/03) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. GENERAL IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed.
4 Pelco Manual C1405M-E (1 1/03) DESCRIPTION Environmental enclosures in the EH4700 Series are used with pan/tilt units or fixed mounts. The enclosures are constructed of aluminum. Y ou can install cameras with either fixed focal length lenses or motorized zoom lenses (up to 10X).
Pelco Manual C1405M-E (1 1/03) 5 INST ALLA TION 1. Unlatch and raise the enclosure lid. The gas spring will hold the lid in place when it is fully opened. 2. Remove the camera sled from the rail: a. Loosen the screws. b. Slide the sled so that the screws are in the large part of the mounting holes.
6 Pelco Manual C1405M-E (1 1/03) c. Move the fan out of the way and remove the fan shroud. d. T urn the fan around so that it blows toward the viewing window (refer to the arrows on the fan). e. Reinstall the fan on the back of the enclosure. f. Close the enclosure lid.
Pelco Manual C1405M-E (1 1/03) 7 Figure 2. EH4700 Series Input Wiring Diagram CAMERA POWER 24/120/230 V AC (SUPPLIED WITH PCB) * CAMERA POWER INPUT TO CAM 2* CAMERA POWER (SUPPLIED WITH PCB) * * CONNECT CAM 1 TO CAMERA WHEN CAMERA'S POWER IS THE SAME AS THE AC POWER INPUT .
8 Pelco Manual C1405M-E (1 1/03) b. Wire the 10-connector INPUTS terminal on the circuit board to the lens controller as follows: • Lens Common - Connector 1 • Focus - Connector 2 • Zoom - Conne.
Pelco Manual C1405M-E (1 1/03) 9 Maximum distance from transformer to load T able A. 24 V AC Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
10 Pelco Manual C1405M-E (1 1/03) 13. EH4718-1, -2, -3 Models, and EH4722-1, -2, -3 Models Only - Wire power to the enclosure to operate accessories (and the camera if its power is con- nected to CAM 1 on the circuit board) as follows: a. Remove the plastic cover over the power supply section of the circuit board.
Pelco Manual C1405M-E (1 1/03) 11 OPERA TION If your enclosure has a thermostatically controlled blower , the thermostat is set to turn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and to turn the fan off between 62 ° and 78 ° F (17 ° and 26 ° C).
12 Pelco Manual C1405M-E (1 1/03) MAINTENANCE Perform the following maintenance at regularly scheduled intervals to prolong the operational life and appearance of the equipment. 1. Clean the window with a mild nonabrasive detergent in water and a soft cloth to maintain picture clarity .
Pelco Manual C1405M-E (1 1/03) 13 ELECTRICAL Input Voltage: 24, 120 or 230 VAC, 50/60 Hz Electrical Connections: One each of the following when equipped with optional circuit board (O/I-PCB): 3-connec.
14 Pelco Manual C1405M-E (1 1/03) (43.18 x 13.97 x 10.80 cm) EH4718-1, -2, -3 13" L x 4.75" W x 4.25" H (33.02 x 12.07 x 10.80 cm) EH4722 21" L x 5.5" W x 4.25" H (53.34 x 13.97 x 10.80 cm) EH4722-1, -2, -3 17" L x 4.
Pelco Manual C1405M-E (1 1/03) 15 increase inside enclosure with heater operating: With vent grills installed: 17 ° F (9.5 ° C) increase With vent covers and TI47 thermal installation: 25 ° F (13.8 ° C) increase With vent covers, TI47 thermal insulation and WD47 defroster installed: 35 ° F (19.
16 Pelco Manual C1405M-E (1 1/03) REVISION HISTOR Y Manual # Date Comments C1405M 10/94 Original version. C1405M-A 12/94 Revised to include new PCB9000276 wiring diagram and parts list as per ECO#94-578. C1405M-B 8/95 Revised Figure 1 to include new PCB9000277ASSY per ECO# 95-255.
デバイスPelco c1405M-Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco c1405M-Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco c1405M-Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco c1405M-Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco c1405M-Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco c1405M-Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco c1405M-Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco c1405M-Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco c1405M-Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。