PelcoメーカーC1487M-Hの使用説明書/サービス説明書
ページ先へ移動 of 24
SD5 Series Spectra II™ and Spectra Lite™ Dome Systems Installation Manual C1487M-H (1/01) ® Pelco • 3500 Pelco W ay • Clovis, CA 93612-5699 USA • www .
2 Pelco Installation Manual C1487M-H (1/01).
Pelco Installation Manual C1487M-H (1/01) 3 CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS .............................................................................................. ...................... 4 INST ALLA TION ...............
4 Pelco Installation Manual C1487M-H (1/01) IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
Pelco Installation Manual C1487M-H (1/01) 5 INST ALLA TION The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes. Inspect each box to make sure all parts are present.
6 Pelco Installation Manual C1487M-H (1/01) HARD CEILING INST ALLA TION IN-CEILING MODELS STEP 1 - PREP ARE CEILING b. Draw a circle on the ceiling using the compass tool and a pencil. Cut the circle out of the ceiling. STEP 2 - INST ALL THE BACK BOX a.
Pelco Installation Manual C1487M-H (1/01) 7 STEP 3 - INST ALL DOME DRIVE a. Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address. Refer to the labels on the dome drive or T ables C through E in the Appen- dix in the back of this manual.
8 Pelco Installation Manual C1487M-H (1/01) SUSPENDED CEILING INST ALLA TION IN-CEILING MODELS STEP 1 - PREP ARE CEILING TILE NOTE: The ceiling tile cannot be thinner than 0.50-inch (1.27 cm) or thicker than 1.75-inches (4.45 cm). a. Remove the ceiling tile from the ceiling.
Pelco Installation Manual C1487M-H (1/01) 9 STEP 3 - INST ALL DOME DRIVE a. Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address. Refer to the labels on the dome drive or T ables C through E in the Appen- dix in the back of this manual.
10 Pelco Installation Manual C1487M-H (1/01) PENDANT -MOUNT INST ALLA TION PENDANT MODELS STEP 1 - MOUNT AND INST ALL THE BACK BOX NOTE: If installing outdoors make sure the installation is properly sealed to keep moisture out. a. Install the mount for the pendant dome.
Pelco Installation Manual C1487M-H (1/01) 11 STEP 3 - INST ALL DOME DRIVE a. Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address. Refer to the labels on the dome drive or tables C through E in the Appendix in the back of this manual.
12 Pelco Installation Manual C1487M-H (1/01) SURF ACE-MOUNT INST ALLA TION PENDANT MODELS STEP 1 - REMOVE THE TOP PORTION OF THE BACK BOX a. T urn the thumbscrew and open the hinged door located inside the back box. b. Unscrew the three Phillips screws lo- cated underneath the hinged door .
Pelco Installation Manual C1487M-H (1/01) 13 STEP 4 - INST ALL DOME DRIVE a. Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address. Refer to the labels on the dome drive or T ables C through E in the Appen- dix in the back of this manual.
14 Pelco Installation Manual C1487M-H (01/01) TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Check to see if the red LED on the circuit board in the back box is lit. 1. The red LED is not lit . a. Fuse is bad. b. 24 V AC power source is not con- nected or back box is bad.
Pelco Installation Manual C1487M-H (01/01) 15 APPENDIX T able A. V ideo Coaxial Cable Wiring Distances Cable T ype* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) * Minimum cable requirements: 75 ohms impedance. All-copper center conductor .
16 Pelco Installation Manual C1487M-H (01/01) T able D. Switch Settings for SW2 – P-T ype Control NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF .
Pelco Installation Manual C1487M-H (01/01) 17 T able E. Switch Settings for SW2 – D-T ype Control (continued) (Continued on next page) Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 S.
18 Pelco Installation Manual C1487M-H (1/01) T able E. Switch Settings for SW2 – D-T ype Control (continued) Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 161 ON OF.
Pelco Installation Manual C1487M-H (1/01) 19 SPECIFICA TIONS MECHANICAL Construction Back box: Aluminum Dome drive: Aluminum, ABS plastic Lower dome: Acrylic Cable Entry In-Ceiling: .
20 Pelco Installation Manual C1487M-H (1/01) 6.60 (16.76) 5.25 ( 13.34) 3.25 (8.26) 7.25 (18.13) 8.25 (20.96) 5.90 (14.99) NOTE: V ALUES IN P ARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. Figure 1. SD5 Series Dimension Drawing 5.90 (14.99) 10.90 (27.
Pelco Installation Manual C1487M-H (1/01) 21 CAMERAS COLOR (Spectra II and Spectra Lite) Signal Format: NTSC (Spectra II dome drive models DD5BC, DD5BC22, and DD5BCBW) PA L (Spectra II dome drive mode.
22 Pelco Installation Manual C1487M-H (1/01) Sensitivity Spectra II 16X: .05 lux at 1/2-second shutter speed 18X: .2 lux at 1/4-second shutter speed (color) .013 lux at 1/4-second shutter speed (black & white) 22X: .07 lux at 1/1.5-second shutter speed Spectra Lite: 1 lux at f1.
Pelco Installation Manual C1487M-H (1/01) 23 Shutter Speed: Automatic (electronic iris)/manual EIA: 1/60-1/30,000 CCIR: 1/50-1/30,000 Iris Control: Automatic with manual override* Gain Control: Automatic with manual override* V ideo Output EIA: .714V ± .
REVISION HISTOR Y Manual # Date Comments C1487M 7/98 Original version. C1487M-A 11/98 Revised the manual to incorporate Spectra Lite material. Added material on CCIR and EIA monochrome cameras, and P A L color camera. Revised material in Section 5.1 1.
デバイスPelco C1487M-Hの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C1487M-Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C1487M-Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C1487M-Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C1487M-Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C1487M-Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C1487M-Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C1487M-Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C1487M-Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。