PelcoメーカーC1498M-Aの使用説明書/サービス説明書
ページ先へ移動 of 20
Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108 Inte.
2 Pelco Manual C1498M-A (7/99) LIST OF ILLUSTRA TIONS Figur e Page 1 System Components (In-Ceiling Model Shown) ................................................ 3 2 Backlight ............................................................................
Pelco Manual C1498M-A (7/99) 3 IMPOR T ANT SAFEGUARDS AND W ARNINGS Observe the following warnings before installing and using this product. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
4 Pelco Manual C1498M-A (7/99) 2. Set the switches on the bottom of the dome drive. Refer to T able A for the settings for SW1, and T able B and T able C for SW2. 3. Install the dome drive in the back box. Line up the green tab and red tab on the dome drive with the green label and red label on the back box.
Pelco Manual C1498M-A (7/99) 5 Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF.
6 Pelco Manual C1498M-A (7/99) Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 57 ON OFF OFF ON ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF OFF 59 ON ON OFF ON ON ON OFF O.
Pelco Manual C1498M-A (7/99) 7 Continued on next page 1 13 ON OFF OFF OFF ON ON ON OFF 1 14 OFF ON OFF OFF ON ON ON OFF 1 15 ON ON OFF OFF ON ON ON OFF 1 16 OFF OFF ON OFF ON ON ON OFF 1 17 ON OFF ON .
8 Pelco Manual C1498M-A (7/99) Continued on next page 169 ON OFF OFF ON OFF ON OFF ON 170 OFF ON OFF ON OFF ON OFF ON 171 ON ON OFF ON OFF ON OFF ON 172 OFF OFF ON ON OFF ON OFF ON 173 ON OFF ON ON OF.
Pelco Manual C1498M-A (7/99) 9 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON .
10 Pelco Manual C1498M-A (7/99) P AN AND TIL T FUNCTIONS Use your controller ’s joystick to control pan and tilt operation. • Fixed-Speed Controllers - Pan and tilt operation is at a fixed speed; the controller determines the speed. • Variable-Speed Contr ollers - Depending on the joystick’s position, standard pan operation ranges from 0.
Pelco Manual C1498M-A (7/99) 11 Software controls scan limit stops. When the dome reaches one, it immediately reverses direction. Refer to the Limit Stops section to program the scan limit stops. Program preset 96 (29) to stop a scan. Any pan and tilt or lens command also stops a scan.
12 Pelco Manual C1498M-A (7/99) CM9750 1. T urn the KEY SWITCH to the ON position. 2. Press the PROG key . PROGRAM appears on the LCD screen. 3. Press the PRES key . The PRESET prompt appears. 4. Enter 95 and press the ENTER key . The main menu appears.
Pelco Manual C1498M-A (7/99) 13 T urning off power to the dome does not reset the camera. Camera settings are retained in memory , and when power is restored, the settings are the same as when the camera was turned off. T o reset the camera: 1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera.
14 Pelco Manual C1498M-A (7/99) 2. If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera. 3. Press the Iris Open button to enter the Camera submenu. 4. Move the joystick up or down to position the cursor beside Auto-Iris.
Pelco Manual C1498M-A (7/99) 15 SHARPNESS The two modes for adjusting the picture sharpness are automatic and manual. T o change the mode: 1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera. 2. Press the Iris Open button to enter the Camera submenu.
16 Pelco Manual C1498M-A (7/99) • Park – The dome moves to preset 1 when the power-up sequence finishes. The only text on the screen is the preset label (if any). • Scan Auto – The dome initiates scan mode when the power-up sequence finishes. Again, there is no text.
Pelco Manual C1498M-A (7/99) 17 SCAN LIMIT STOPS Refer to the documentation for your control system for programming presets, then do the following: 1. Make sure limit stops are turned ON (refer to the Limit Stops section), then exit the menu. 2. Push the joystick left until you reach the limit you want the camera to go to on the left.
18 Pelco Manual C1498M-A (7/99) 4. Remove the dome drive: Push in on the green drive eject tab on the side of the dome drive and gently rock the dome drive to release the latch. When the green latch releases, pull the dome down. 5. Do one of the following: • If your problem was that the unit would not operate: Proceed to step 6.
Pelco Manual C1498M-A (7/99) 19 SPECIFICA TIONS MECHANICAL Pan Movement: 360 ° continuous pan rotation Vertical Tilt: Unobstructed +2 ° to -92 ° Manual Pan Speed: 0.
20 Pelco Manual C1498M-A (7/99) REVISION HISTOR Y Manual # Date Comments C1498M 2/99 Original version. 3/99 Removed reference to line synchronization. Added material on auto iris. Added FCC notice. C1498M-A 7/99 Revised the preset tilt speed from 100 to 200 degrees/second.
デバイスPelco C1498M-Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco C1498M-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco C1498M-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco C1498M-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco C1498M-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco C1498M-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco C1498M-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco C1498M-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco C1498M-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。