PelcoメーカーDX8000の使用説明書/サービス説明書
ページ先へ移動 of 20
DX8000-256RAM Installation Manual C1602M (6/04) Digital Video Recorder DX8000.
Protecting people and property in a million locations worldwide..
C1602M (6/04) 1 Introduction The following instructions serve as a guide for the installation of the DX8000-256RAM memory expansion module. PARTS LIST Qty Description 1 256 MB double data rate (DDR) dual inline memory module (DIMM) 1 Adhesive-backed upgrade part label Figure 1.
2 C1602M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools.
C1602M (6/04) 3 Figure 3. Removing Power Cord from Unit.
4 C1602M (6/04) Figure 4. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit.
C1602M (6/04) 5 Prepare Unit for RAM Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components.
6 C1602M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section.
C1602M (6/04) 7 COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity .
8 C1602M (6/04) Install the DX8000-256RAM Memory Module 1. Carefully remove the DX8000-256RAM DIMM module from its static-safe packaging. Handle the DIMM by its edges and avoid contact with the module’ s chips or conductive leads. 2. Locate the first empty DIMM socket.
C1602M (6/04) 9 3. Align the DIMM module with the socket so that the notch in the module lines up properly with the break in the DIMM socket. Refer to Figure 8. 4. Make sure that the white retaining clips are not in the locked position by pressing outward and down on each clip.
10 C1602M (6/04) 5. Carefully , but firmly , push the DIMM module into the empty socket until it is properly seated. The module is properly seated when the retaining clips snap back into place as in Figure 9. NOTE: When inserting the DIMM module into the socket, use enough pressure to ensure that the retaining clips snap back into place.
C1602M (6/04) 11 Reassemble the Unit 1. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 10.
12 C1602M (6/04) 2. Attach the silver part label that came in your upgrade kit to the inside of your DVR’ s front door . a. Remove the paper backing from the part label. b. Carefully place the label, adhesive-side down, on a free section of the inside of the door .
C1602M (6/04) 13 3. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 4. Plug the power cord back into the power supply and then into the wall. 5. T urn on the power switch and allow the unit to start up and find the new memory .
14 C1602M (6/04) V erify Installation of New RAM 1. After the DX8000 application starts, log in as an administrator level user and exit to the Windows ® operating system. Refer to the Installation or Operations and Programming manuals that came with your unit for instructions.
C1602M (6/04) 15 4 4. V erify that the amount of RAM is now 512 MB. Refer to Figure 15. Figure 15. System Properties Dialog Box 5. Click OK to exit the System Properties dialog box. 6. Go to Start > Programs > DX8000 to start the DX8000 application and return the unit to service.
16 C1602M (6/04) Notes.
PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
C1602M (6/04) ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
デバイスPelco DX8000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco DX8000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco DX8000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco DX8000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco DX8000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco DX8000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco DX8000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco DX8000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco DX8000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。