PelcoメーカーMC3600H-2の使用説明書/サービス説明書
ページ先へ移動 of 16
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel +1 (559) 292-1981 or FAX +1 .
[ 2 ] Pelco Manual C1982M-A (12/00).
Pelco Manual C1982M-A (12/00) [ 3 ] CONTENTS IMPORT ANT SAFEGUARDS AND W ARNINGS ................................................................................. 4 REGULA TOR Y NOTICES .................................................................
[ 4 ] Pelco Manual C1982M-A (12/00) IMPORT ANT SAFEGU ARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installation personnel.
Pelco Manual C1982M-A (12/00) [ 5 ] DESCRIPTION The MC3500 and MC3600 Series are compact, monochrome video cameras with a 1/3-inch CCD imager . All cameras have a direct drive/auto iris lens connector and adjustable back focus, and accept C and CS lenses.
[ 6 ] Pelco Manual C1982M-A (12/00) CAMERA LA Y OUT Figure 1. Camera Layout NOTE: The cosmetic trim ring conceals the LED light for more discreet surveillance operations.
Pelco Manual C1982M-A (12/00) [ 7 ] 3 4 12 PIN DD LENS CONNECTIONS AI LENS CONNECTIONS 1 Control coil negative (-) Not used 2 Control coil positive (+) Lens positive supply 3 Drive coil positive (+) Video drive signal 4 Drive coil negative (-) Ground Figure 2.
[ 8 ] Pelco Manual C1982M-A (12/00) POWER AND VIDEO CONNECTIONS T o connect the camera power and video do the following: 1. Remove the rear cover from the camera (refer to Figure 1).
Pelco Manual C1982M-A (12/00) [ 9 ] Table A. Recommended Wire Gauge and Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
[ 10 ] Pelco Manual C1982M-A (12/00) LENS SETUP AND FOCUS PR OCEDURES Video Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AI. Switch the EI and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video out- put level of 1V peak-to-peak).
Pelco Manual C1982M-A (12/00) [ 11 ] BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. T o adjust the back focus: 1. Loosen the two back focus locking screws (one on each side).
[ 12 ] Pelco Manual C1982M-A (12/00) SWIT CH SETTINGS Figure 7. Switch Settings 10 LL/INT Synchronization Selection Locks the frame rate to the power supply frequency . Eliminates vertical roll caused by multiple cameras connected to the same switching de- vice.
Pelco Manual C1982M-A (12/00) [ 13 ] 4 EI ON/EI OFF (Electronic Iris) The EI (Electronic Iris) feature compensates for an excessive light level by automatically adjusting shutter speed. When the EI is ON, the DD lens level potentiometer on the side of the camera may be used to adjust the EI threshold level.
[ 14 ] Pelco Manual C1982M-A (12/00) CAMERA PHASE ADJUSTMENT When using one AC power supply in a multi camera system, a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll, adjust the phase control to synchronize (line-lock), the cameras to one another .
Pelco Manual C1982M-A (12/00) [ 15 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch Synchronization System: AC line lock or internal oscillator Horizontal Resolution MC3500S-2: 380 TV lines MC3600H-2: 570 TV lines Iris Control: Electronic/passive Minimum Illumination MC3500S-2: 0.
[ 16 ] Pelco Manual C1982M-A (12/00) Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation.
デバイスPelco MC3600H-2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco MC3600H-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco MC3600H-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco MC3600H-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco MC3600H-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco MC3600H-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco MC3600H-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco MC3600H-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco MC3600H-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。