PelcoメーカーWD57の使用説明書/サービス説明書
ページ先へ移動 of 20
BK57 Blower , HK57 Heater , O/I-PCB and WD57 Defr oster Kits for EH5700/EH5700L Series Envir onmental Enclosur es Installation/ Operation Manual C1423M-D (10/03) 00972 ® Pelco • 3500 Pelco W ay • Clovis, CA 93612-5699 USA • www .
2 Pelco Manual C1423M-D (10/03) REVISION HISTOR Y Manual # Date Comments C1423M 6/95 Original manual. C1423M-A 4/96 Rev . A. Incorporated Manual C1424M for blower kits. Incorporated Manual C1425M for defroster kits. Added instructions for installation of O/I-PCB circuit board kit.
Pelco Manual C1423M-D (10/03) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed.
4 Pelco Manual C1423M-D (10/03) 2.0 DESCRIPTION The information in this manual covers the installation and operation of the following kits for the EH5700/EHS700L Series environmental enclosures: BK57-.
Pelco Manual C1423M-D (10/03) 5 3.0 BLOWER KIT INST ALLA TION This section provides instructions for installing the BK57-1. BK57-2. and BK57-3 blower kits. For the following instructions, refer to Figure 1. T able B lists the parts shown in Figure 1. 1.
6 Pelco Manual C1423M-D (10/03) W ire Gauge Maximum distance from transformer to load T able A. 24 V AC Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
Pelco Manual C1423M-D (10/03) 7 11 . Thermostatically Controlled Operation Only (O/I-PCB Installed) - If the circuit board for thermostatic control of the fan already is installed, complete the installation as follows: a. Remove the plastic power supply barrier cover from the circuit board.
8 Pelco Manual C1423M-D (10/03) T able B. Exploded Assembly Parts List for Blower Item Qty Description Part Number 11 V ent Grill, Beige 57004105COMP 1V ent Grill, Gray 57004005COMP 22 Foam Filter EH5.
Pelco Manual C1423M-D (10/03) 9 4.0 HEA TER KIT INST ALLA TION This section provides instructions for installing the HK57-1, HK57-2, and HK57-3 heater kits. For the following instructions, refer to Figure 2. T able C lists the pans shown in Figure 2. 1.
10 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 11 Bracket/Heat sink 57004020COMP 22 Heater , 230 V AC HTR40220 2 Heater , 24 V AC HTR20024 2 Heater , 120 V AC HTR50120 31 Connector CON1-480424-0 A2 Spacer , .
Pelco Manual C1423M-D (10/03) 11 5.0 DEFROSTER KIT INST ALLA TION This section provides instructions for installing the WD57-1, WD57-2, and WD57-3 defroster kits. For the following instructions, refer to Figure 3. T able D lists the parts shown in Figure 3.
12 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 11 Window Defroster , 120 V AC 570010003 1W indow Defroster , 24 V AC 570010006 1W indow Defroster , 230 V AC 570010005 21 Connector Plug CON1-480318-0 T able D. Exploded Assembly Parts List for Defroster Figure 3.
Pelco Manual C1423M-D (10/03) 13 6.0 CIRCUIT BOARD KIT INST ALLA TION This section provides instructions for installing the O/I-PCB circuit board kit. For the following instructions, refer to Figure 4. T able E lists the parts shown in Figure 4. 1. Install the circuit board kit (O/I-PCB): a.
14 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 1 Not Used 2 Not Used 3 Not Used 41 Power Supply Barrier Cover EH470010019 52 Power Supply Barrier EH47004029COMP 61 Circuit Board PCB9000276ASSY 71 Circuit Board Insulator EH450010256 A Not Used B2 Internal T ooth Lock W asher , #4 ZH4L WSIS C2 Screw 4-40 x 1/4", Pan Head.
Pelco Manual C1423M-D (10/03) 15 8. Refer to Figure 5 and connect the camera’s power input to the circuit board. When the power requirements are the same, there are two ways to connect power: (1) A three-pin plug is supplied as loose equipment.
16 Pelco Manual C1423M-D (10/03) Figure 5. Input Wiring Diagram 00967.
Pelco Manual C1423M-D (10/03) 17 7.0 OPERA TION If your enclosure has a thermostatically controlled blower , the thermostat is set to turn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and .
18 Pelco Manual C1423M-D (10/03) Figure 6. Wiring Diagram for Optional Circuit Board (O/I-PCB) 00970.
Pelco Manual C1423M-D (10/03) 19 Figure 7. Circuit Board Component Locations Figure 8. Circuit Board Layout of T races 00971.
20 Pelco Manual C1423M-D (10/03) 9.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved.
デバイスPelco WD57の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pelco WD57をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPelco WD57の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pelco WD57の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pelco WD57で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pelco WD57を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPelco WD57の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pelco WD57に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPelco WD57デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。