Pellaメーカー818L0100の使用説明書/サービス説明書
ページ先へ移動 of 16
INST ALLA TION INSTRUCTION - INSTRUCCIONES DE INST ALACION CLAD HINGED P A TIO DOOR — (INCLUDES ST ANDARD, PERFORMANCE UPGRADE AND HURRICANESHIELD ® IMP ACT RESIST ANT IN-SWING AND OUT -SWING) Part.
e performance of any building is dependent upon the design, installation, and workmanship of the entire building system. P ella Corporation strongly recommends consulting an experienced architect, contractor or structural engineer prior to installation of P ella products.
FOR DOORS USING OPTIONAL SILL P AN GO T O STEP 1I . Exterior 1D 4th cut: Make a 6" cut up from each top corner at a 45 o angle to allow the water resistive barrier to be lapped over the fin at the head of the door . 1st cut 2nd cut 3rd cut Water Resistive Barrier 1C C.
Optional Sill P an Instructions: I. Cut the sill pan to the width of the rough opening plus 2”. N ote: e 2” added onto the rough opening width is for a 1” bend on each end. J. Make a 1” cut in each fold at both end of the sill pan. N ote: ese cuts will allow the edges of the sill pan to be bent.
2 PREP ARE THE DOOR FOR INST ALLA TION TWO OR MORE PEOPLE WILL BE REQUIRED T O HANDLE THE P ANEL AND FRAME SAFEL Y . A. Remo ve plastic wrap and car dboard packaging from door . Do not remov e plastic shipping spacers. e shipping spacers will help keep the door square during installation.
Applications for P erformance Upgrade and H urricaneShield: 6" 16" MAX O.C. 16" MAX O.C. 16" MAX O.C. 16" MAX O.C. 6" 6" 6" 6" 6" 6" 6" DOUBLE OPERABLE 6" 6" 16" MAX. O.C. 2C 6" 6" 16" MAX.
TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLL O WING STEPS: B. Cut and remo ve the strap that runs from the door lock to the sill of the door . C. Insert the door from the exterior of the building. DO NO T slide the bottom of the door into the opening.
F. F asten the door to opening by driving 2” galvanized roong nails into each pre-punched hole in the nailing n. N ote: Make sure the n corner is lying as at as possible. Exterior 3H 3F Interior 3K 3J G. Carefully open the door(s) and remo ve all shipping spacers.
K. Shim betw een the frame and the rough opening at the head strike location and at ev er y frame anchor hole location. Remov e and replace head strike screws with three #8 x 3” corrosion resistant screws (pro vided) through the head strike, door frame, shims and into the rough opening.
4 INTEGRA TING THE DOOR TO THE WA TER RESISTIVE BARRIER A. Apply side ashing tape. C ut two pieces of ashing tape 4" longer than the frame height of the door . Apply one piece 1/2" onto the frame cladding, over the nailing fin and onto the water resistive barrier on each side.
5 INST ALL THE F ASTENERS FOR PERFORMANCE UPGRADE OR HURRICANESHIELD PRODUCT F rame Screw M ethod: N ote: If installing with installation clips, proceed to Step E.
5F EXTERIOR INTERIOR Drill 1/8” diameter pilot holes through the clearance hole in the frame. 5C Out-Swing #10 x 3-1/2" corrosion resistant wood screw 5D EXTERIOR INTERIOR 5G 5E 5D SILL HEAD D.
6 INTERIOR SEAL A. Apply insulating foam sealant. F rom the interior , inser t the nozzle of the applicator into the space between the door and the rough opening approximately 1” past the edge of the frame (and past the jamb extensions) and apply a 1" deep bead of foam.
7 SEALING THE DOOR TO THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other exterior nish material, leave adequate space between the door frame and the material for sealant. Refer to the illustr ation that corresponds to your nish material.
INTERIOR FINISHING If products cannot be nished immediately , cover with clear plastic to protect from dirt, damage and moisture. Remo ve any construction residue before nishing. Sand all wood surfaces lightly with 180 grit or ner sandpaper .
TROUBLESHOOTING - Adjustable Strike Latching Issues T ABS Adjustable strike shim (side view) Strike (front view) Adj. Strike Shim (end view) Factory installed side Side to be used in Issue 2 Issue 2: Door needs to close more tightly against the weather-strip.
デバイスPella 818L0100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pella 818L0100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPella 818L0100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pella 818L0100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pella 818L0100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pella 818L0100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPella 818L0100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pella 818L0100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPella 818L0100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。