Pellaメーカー818T0101の使用説明書/サービス説明書
ページ先へ移動 of 16
P art Number: 818T0101 © 2011 P ella Corpor ation Sill Flashing T ape #2 Sill Flashing T ape #1 Sill Support To p Flashing T ape Side Flashing T ape Wea ther Resistive Barrier F raming Sheathing Installation Instructions for T ypical Wood F rame C onstruction.
Y OU WILL NEED T O SUPPL Y : T OOLS REQUIRED: Ř Composite/impervious shims/spacers (12 to 20) Ř #8 x 3" corrosion r esistant woodscrews Ř 16d galvanized finish nails or exterior grad.
D. Cut the weather resistive barrier , if applicable (1D). 4th cut: Make a 6" cut up fr om each top corner at a 45° angle to allow the weather barrier to be lapped over the fin at the head of the door . 1st cut 2nd cut 3rd cut W ater Resistive Barrier 1D 1D E.
2 PREP ARE THE DOOR FOR INST ALLA TION TWO OR MORE PEOPLE WILL BE REQUIRED T O HANDLE THE P ANEL AND FRAME SAFEL Y . A. Remove plastic wr ap and cardboar d packaging fr om door . DO NOT remove plastic shipping spacers. T he shipping spacers will help keep the door square during installation.
81-1/2" 81-1/2" 3" 3" 21" 9-1/4" 9-1/4" 3" 3" 21" 21" 3" 3" 21" 6-3/4" 6-3/4" 3" 3" 21" 21" 97-1/2" 21" 97-1/2" 6" 6" 6" 6" 6" 6" = Screw or clip location other than at hinge or strike.
A. If unit is equipped with a screw type pre-hanging plug for tr ansporting, remove the scr ew portion fr om the exterior of the jamb before setting the door . Note: If a brickmould/exterior trim is being added to the door, install and seal it to the frame a t this time.
E. Plumb and Square Door . Shim unit in place by driving in shims from the interior . Shim behind each hinge, at each screw or clip loca tion, and behind the dead bolt lockstrike.
3 SETTING AND F ASTENING THE DOOR (CONTINUED) CORRECT INCORRECT 2G 3F F. Car efully open the door and remove all shipping spacers. Remove pr e-hang plug from the bor e hole. Car efully open and close the door . Check for even contact between the door panel and weatherstrip on both jambs and across the head.
3 SETTING AND F ASTENING THE DOOR (CONTINUED) N. Check for suf ficient weatherstrip contact between the bottom weatherstrip and the thr eshold. Close the door on a dollar bill or sheet of paper located above an adjustment screw; light friction should be felt when pulling the paper out indicating a good seal is being made.
O. If needed, the height of the threshold can be adjusted to achieve appropria te contact with the door sweep. Remove screw cover caps as necessary and use a #3 Phillips screwdriver to turn the adjustment screws clockwise to lower the threshold or counter -clockwise to raise the threshold.
E. Install top flashing tape. Cut one piece of flashing tape 2" wider than the width of the top brickmould. Apply the top flashing tape so it extends 1" beyond the end of the top brickmould. P osition the tape so it covers the vertical leg of the aluminum flashing and laps onto the sheathing above the door .
5 INTERIOR SEAL Caution: Ensur e use of low pressure polyurethane window and door installation foams and strictly follow the foam manufacturer’ s recommendations for applica tion. Use of high pressure foams or improper application of the foam may cause the door to bow and hinder operation.
Note: When applying siding, brick veneer or other exterior finish materials, leave adequate space between the door fr ame and the material for sealant.
A. Insert back er rod into the space ar ound the door so there is appr oximately 1/2" clearance between the back er rod and the face of the door frame. Note: Backer r od adds shape and depth for the sealant line. B. Apply a bead of high quality exterior grade sealant to the entir e perimeter of the door.
FINISHING INSTRUC TIONS P aint or finish immediately after installation. Note: DO NO T paint, stain or finish weather strip or vinyl parts! If paint, stain or finish gets on the weather stripping, wipe it off immediately with a damp cloth. T o maintain proper product performance, do not remove wea ther strip, foam corner seal wedges or gaskets.
IMPORT ANT NO TICE Because all construction must anticipate some water infiltr ation, it is important that the wall system be designed and constructed to properly manage moistur e.
デバイスPella 818T0101の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pella 818T0101をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPella 818T0101の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pella 818T0101の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pella 818T0101で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pella 818T0101を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPella 818T0101の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pella 818T0101に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPella 818T0101デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。