PentairメーカーVS-3050の使用説明書/サービス説明書
ページ先へ移動 of 40
IMPOR T ANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SA VE THESE INSTRUCTIONS Inst allation and User ’ s Guide IntelliFlo ® VS-3050 V ariable S peed Programmable Pump (Compatible with I.
© 2008 Pentair Water Pool and Spa, Inc. All rights reserved This document is subject to change without notice 1620 Hawkins A ve., Sanford, NC 27330 • (919) 566-8000 10951 West Los Angeles A ve.
i IntelliFlo VS-3050 Installation and User’ s Guide Important Safety Precautions ........................................................................................... ii Section 1: IntelliFlo VS-3050 Overview ..................................
ii IntelliFlo VS-3050 Installation and User’ s Guide Import ant Notice: Attention Installer: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner and/or operator of this equipment.
iii IntelliFlo VS-3050 Installation and User’ s Guide IMPORTANT SAFETY PRECAUTIONS (continued) W ARNING — Water temperature in excess of 100° Fahrenheit may be hazardous to your health.
iv IntelliFlo VS-3050 Installation and User’ s Guide General Inst allation Information W ARNING — Pumps improperly sized or installed or used in applications other than for which the pump was intended can result in severe personal injury or death.
1 IntelliFlo VS-3050 Installation and User’ s Guide Section 1 Overview IntelliFlo ® VS-3050 V ariable Speed Pump The IntelliFlo VS-3050 variable speed pump is well suited for all of your pool, spa, cleaner , waterfall and other water application.
2 IntelliFlo VS-3050 Installation and User’ s Guide Features • Adjusts to various pool sizes • Prevents thermal overload • Detects and prevents damage from under and over voltage conditions .
3 IntelliFlo VS-3050 Installation and User’ s Guide IntelliFlo VS-3050 Drive Assembly and Control Panel The IntelliFlo drive assembly consists of an operator control panel and the system electronics that drive the motor .
4 IntelliFlo VS-3050 Installation and User’ s Guide Controls and LEDs Speed 1, Speed 2, Speed 3, and Speed 4 button/LED: Press one of the speed buttons to select the desired preset pump speed. The pump preset speeds are: Speed 1 (750 RPM), Speed 2 (1500 RPM), Speed 3 (2350 RPM), and Speed 4 (31 10 RPM).
5 IntelliFlo VS-3050 Installation and User’ s Guide Section 2 Operating IntelliFlo VS-3050 This section describes how to use the IntelliFlo VS-3050 pump control panel. Setting the pump preset speed IntelliFlo operates using one of the preset speeds.
6 IntelliFlo VS-3050 Installation and User’ s Guide S t arting the pump T o st art the pump 1. Ensure that the pump is powered on and the green power LED is on.
7 IntelliFlo VS-3050 Installation and User’ s Guide Priming the pump for the first time, or af ter service Before the IntelliFlo VS-3050 pump is started for the first time it must be primed. T o prime a pump means filling the pump and suction pipe with water .
8 IntelliFlo VS-3050 Installation and User’ s Guide Priming the pump for the first time, or af ter service (Continued) Priming the Pump • Release all pressure from filter , pump, and piping system; see the filter owner ’ s manual.
9 IntelliFlo VS-3050 Installation and User’ s Guide External Control with IntelliComm Communication Center The IntelliFlo VS-3050 can be remotely controlled by the Pentair IntelliComm Communication Center using an optional communications cable (P/N 350122).
10 IntelliFlo VS-3050 Installation and User’ s Guide Connecting IntelliFlo VS-3050 to an EasyT ouch System The IntelliFlo can be controlled by an EasyT ouch system via the RS-485 communication cable (P/N 350122). In this configuration, EasyT ouch starts, stops and controls the speed of the IntelliFlo pump.
11 IntelliFlo VS-3050 Installation and User’ s Guide 5. Lower down the hinged control panel to access the EasyT ouch motherboard. 6. Route the communication cable into the lower plastic grommet, up through the low voltage raceway to the EasyT ouch load center motherboard.
12 IntelliFlo VS-3050 Installation and User’ s Guide EasyT ouch Load Center (front view) Control panel access screw Control panel access screw High voltage cover panel Retaining screw 10. Close the control panel into its original position and secure it with the two access screws.
13 IntelliFlo VS-3050 Installation and User’ s Guide Connecting IntelliFlo VS-3050 to an IntelliT ouch System The IntelliFlo VS-3050 can be controlled by an IntelliT ouch system via the RS-485 communication cable (P/N 350122). In this configuration, IntelliT ouch starts, stops and controls the speed of the IntelliFlo pump.
14 IntelliFlo VS-3050 Installation and User’ s Guide 6. Strip back the cable conductors ¼”. Insert the wires into the either of the COM POR TS (J7 andJ8) screw terminals located on the left side of the Personality board. Secure the wires with the screws.
15 IntelliFlo VS-3050 Installation and User’ s Guide Connecting IntelliFlo VS-3050 to a SunT ouch System The IntelliFlo VS-3050 can be controlled by a SunT ouch system via the RS-485 communication cable (P/N 350122).
16 IntelliFlo VS-3050 Installation and User’ s Guide Blank Page.
17 IntelliFlo VS-3050 Installation and User’ s Guide Section 3 User Maintenance The following information describes how to service and maintain the IntelliFlo VS-3050 pump. Pump Strainer Basket The strainer , sometimes referred to as the “Hair and Lint Pot,” is in front of the of the pump.
18 IntelliFlo VS-3050 Installation and User’ s Guide Motor Service 1. Protect from heat: • Shade the motor and controller from the sun. • Any enclosure must be well ventilated to prevent overheating. Particular attention should be paid to the motor fan cover and the cooling fins between the drive and the motor.
19 IntelliFlo VS-3050 Installation and User’ s Guide Priming the pump af ter service Before a system start-up, the pump and system must be manually primed. Make sure to reopen valves before operating. T o prime IntelliFlo, the strainer pot must be filled with water .
20 IntelliFlo VS-3050 Installation and User’ s Guide Blank P age.
21 IntelliFlo VS-3050 Installation and User’ s Guide Section 4 Inst allation and Removal The following information describes how to install the IntelliFlo VS-3050 pump. Note: Before installing this product, read and follow all warning notices and instructions on page ii.
22 IntelliFlo VS-3050 Installation and User’ s Guide Wiring the IntelliFlo VS-3050 T o connect the IntelliFlo to an AC power source: 1. Make sure all electrical breakers and switches are turned off before wiring motor. 2. Make sure that the wiring voltage is 230 VAC ± 10%.
23 IntelliFlo VS-3050 Installation and User’ s Guide Pump Disassembly W ARNING — Always disconnect power to the pool pump at the circuit breaker and disconnect the communication cable before servicing the pump. Failure to do so could result in death or serious injury to serviceman, pool users or others due to electric shock.
24 IntelliFlo VS-3050 Installation and User’ s Guide Pump Disassembly (Continued) 9. T o unscrew the impeller from the shaft, twist the impeller counterclockwise. 10. Remove the rotating portion of the mechanical seal from the impeller . 1 1. Remove the four bolts from the seal plate to the motor , using a 9/16 inch wrench.
25 IntelliFlo VS-3050 Installation and User’ s Guide Drive Assembly Removal and Inst allation T o remove the IntelliFlo VS-3050 drive and control panel from the motor assembly: 1. Make sure all electrical breakers and switches are turned off before removing the drive.
26 IntelliFlo VS-3050 Installation and User’ s Guide Item Part Description No. No. 15 072184 WASHER 3/8 ID X 7/8 OD .05 THICK 18-8 s/s, (QTY 6) 16 072928 DIFFUSER ASSEMBL Y WFE 12 17 073131 I MP ELL.
27 IntelliFlo VS-3050 Installation and User’ s Guide IntelliFlo VS-3050 Pump Dimensions 10.78 12.50 23.41 IntelliFlo VS-3050 Electrical Specifications Circuit Protection: T wo-pole 20 AMP device at the Electrical Panel.
28 IntelliFlo VS-3050 Installation and User’ s Guide Blank Page.
29 IntelliFlo VS-3050 Installation and User’ s Guide W arning and Alarm conditions The IntelliFlo VS-3050 alarms and warnings are indicated by flashing LEDs on the control panel. For example, if a “Drive T emperature” warning occurs, the LED will blink two times, then Off, then blink two times.
30 IntelliFlo VS-3050 Installation and User’ s Guide General IntelliFlo VS-3050 T roubleshooting Problems Use the following general troubleshooting information to resolve possible problems with your IntelliFlo pump. Note: Switch the main power off to the pump before attempting service or repair .
31 IntelliFlo VS-3050 Installation and User’ s Guide Problems and Corrective Action (Continued) m e l b o r Pe s u a C e l b i s s o P n o i t c A e v i t c e r r o C s p i r t r e k a e r b t i u c r i C . y l d e t a e p e r d n a m r a l A o t r e f e R e c n e u q e s D E L g n i n r a w .
32 IntelliFlo VS-3050 Installation and User’ s Guide Notes.
Notes.
P/N 357269 Rev . C *357269*.
デバイスPentair VS-3050の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pentair VS-3050をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPentair VS-3050の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pentair VS-3050の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pentair VS-3050で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pentair VS-3050を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPentair VS-3050の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pentair VS-3050に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPentair VS-3050デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。