Pfaffメーカー28の使用説明書/サービス説明書
ページ先へ移動 of 21
PFAFF 28 Cylinder Bed Right Arm Sewing Machine with Beak Shutt%e INSTRUCTION BOOK G. M. PFAFF AG, Sewing Machine Factory, KAISERSLAUTERN.
FIGURE 8 FRiCTION ‘“LEVER D Page 11.
Page 2 7 3 4 7 7 6 8 8 Section Index 1, Dehvery of the Machine 2. Engaging and Disengaging the Sewing Mechanism Bobbin Case 3. Threading the Needle 4, Winding the Bobbin 5. Changing the Bobbin and Threading the 6. Drawing Up the Bobbin Thread 7. Regulating the Thread Tensans 8.
Instruction Book PFAFF 28 Cylinder Bed Right Arm Sewing Machine Fitted with standard or extra large beak shuttle, link fake-up, knee lever presser foot lifter, reversible drop feed, wooden extension o.
1. Delivery of the Machine Unless shipped directly, every sewing machine, when received at our dealers, is unpacked, carefully checked for possible damage inflicted in transit, cleaned, and tested for perfect sewing before being released For delivery to the customer.
3. ThreadIng the Needle As shown in photo 2, pass the thread from spool 1 through the three slotted holes of thread guide 2, around and between the tension discs 3, through check spring 4, beneath guide 5, through eyelet 6, right-left through take-up 7, through eyelets 8 and 9, needle bar eyelet 10, and then left-right through needle eye 11.
4. Winding the Bobbin All PEAFF 28 machines are equipped with a table winder which hos proved very useful in all sewing shops. As shown in photo 3, place spool 1 on pin 2, and the empty bobbin on spindle 6. Pass the thread from spool 1 through the hole 3, between tenson discs 4, over pin 5, and through the slot in the face of the bobbin.
5. Changing the Bobbin and Threading the Bobbin Case Raise the shuttle race cop by slightly pushing it up with thumb and index finger of your left hand so that it can be slipped over the head of screw a (see photo 4), then let it hong by the hinge screw.
3. Lay both threads back under the presser foot. Basic Role: Stop the machine or commence sewing only with the take.up in its highest position. This precaution will keep the thread from slipping out of the needle eye and will prevent jamming of the thread in the shuttle roce.
The bobbin thread tension is regulated by means oF the small screw driver. Turning tension screw d (see photo 8) clockwise , will increase the tension; turning it coueter-clockwise -< will decrease the tension.
In fig. 12, the needle thread tension may be too loose or the bobbin thread tension too tight. The operator will have to decide in each individual case whether or not either tension requires adjustment, particularly so the thread forms small krots or loops on the upDer or underside of thc material.
If the needles are too thick for the material to be sewn, ugly needle marks will show in the material. With long, thin needles, vibration of the needle can hardly be avoided. Therefore, two needle systems comprising needles of different lengths are used with PFAFF 28 machines, depending on the type of work.
Needle and Thread Chart PFAFF Needle Thread Weight Class of Work Size Cotton 90-60 Rayon 40-30 very fine leather, 8 Silk, continuous fiber 00 flimsy fabrics Silk, staple fiber 24 Cotton 60-40 Rayon 30-24 fine leather, Silk, continuous fiber 0 fine linings Silk, staple fiber 22 Cotton 50-30 medium leather, Rayon 30-24 10 .
1O Inserting the Needle In any case, the needle is to be pushed up in the needle bar as far as it will go and to be fastened securely. Flat-shank needles, System 805, ore to be inserted with the flat side of the shank facing the needle bar.
12. The Knee Lever Presser Foot Lifter With the exception of sub-class 28-15, all PFAFF 28 machines are provid ed with a knee lifter which permits to raise and lower the roller presser or presser foot by knee control and allows the operator to rnaniouiate the work with both hands when performing intricate sewing operations.
The extra arge beak shuttle which is used in canjunction with longer needles is of the same type as the standard-size beak shuttle, the only difference being ts larger size to accomodate a bobbin of a greater capa city.
As a rule, all bearings and parts n movable contact are to be oiled. After the machine has been tilted over (as instructed in poragroph 1 4), the parts inside the vertical part of the arm are eosily occesstble (see photo 16). The machine will repay thorough cleaning and proper oiling with light running and perfect stitching.
Packed dust or fluff should be carefully removed with a pointed pece of wood. Scissors and screw drivers ore unsuitable for this purpose. The lacquer finish of the machine does not require special maintenance. It is sufficient to rub off the machine now and then with same kerosene and to polish it with a soft cloth.
The electric motor calls for practically no maintenance. After a longer period of use, check if there is sufficient grease in the grease bushings. If tilling up is necessary, use only the special motor grease whch we supply in handy tubes. The complete treadle assembly is left on the machine when it is power driven.
19 Probable Causes of Sewing Troubles Skipping of Stitches: 1. Neede inserted incorrectly, grooves facing the wrong way. 2. Other than proper needle system used. 3. Needle bent. 4. Needle threaded incorrectly. 5. Needle inadequate for the thread used.
SEWING MACHINE FACTORY G. M. PFAFF AG, KAISERSLAUTERN Founded 1862 Certificate of Guarantee For every PFAFF Sewing Machine bearing this TRADE and the name MARK PFAFF the factory assumes fu(I guarantee for first-class quality, efficiency, and durability.
デバイスPfaff 28の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pfaff 28をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPfaff 28の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pfaff 28の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pfaff 28で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pfaff 28を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPfaff 28の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pfaff 28に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPfaff 28デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。