Pfaffメーカーhobby 1010の使用説明書/サービス説明書
ページ先へ移動 of 15
INSTRUCTION MANUAL FOR SEWING MACHINE 0] Hobby Model 351427004 0012.14 1010 — 37.
IMF’UHIANT 5AFTY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using (this sewing machine) DANGER To reduce the risk of electric shock: An appliance should never be left unattended when plugged in.
NAME OF PARTS (FRONT VIEW) (REAR VIEW) Thread tension dial Bobbin winder Stop Motion knob Hand wheel Bobbin winder spindle Face cover Presser toot Shuttle Extension table Thumb screw Needle plate Zigz.
ACCESSORIES Bobbin Button foot Button hole cutter Felt Zigzag foot (On machine) Machine Oil Screw driver Button hole foot Zipper foot I Needle #11 #14 BEFORE SEWING 1 Fit plug into the machine. 2. Plug the machine to the po y supply. 3. Sewing speed can be varied the foot control.
REMOVING EXTENSION TABLE 1 Hold the left end of table and pull out in diecfion or arrow. WINDING ThE BOBBIN 1 Release stop motion kric 2.Thread as shown. 3.When bobbIn is filk tighten stop motion kno 1. This sewing machine can be used as a fiat bed machine but easily converts to free arm machine by removing the extension table.
2.Open hinged latch of bobbIn case and pull bobbin case out of machine. INSERTING BOBBIN INTO BOBBIN CASE 1.Raise needle to its highest position, pulling thread to the front, open the latch of bobbin case and hold it. I .PulI off 5cm of thread from bobbin and insert it into bobbin case as shown.
THREADING UPPER THREAD 1. Hold upper thread with left hand, turn the hand wheel slcwly towards you until the needle qoes down and comes up. Then stop the hand wheel when the takeup lever is at its highest position. Lightly draw up the upper tbread and the lower thread will be brought up in a loop.
ADJUSTiNG THREAD TENSION CONTROL DIAL Weak Strong Upper thread tension may be adjusted by turning the thread tension dial. Fabric Coaect Incorrect Inside of fabric Upper thread Upper thread Bobbin tbread LOWER THREAD TENSION Lower thread tension can be adjusted by turning screw on bobbin case slight ly to the right (clock-wise) to increase tension.
REGULATING THE PRESSER FOOT PRESSURE 1. Push down inner pin (A) to increase pressure. (Light to medium fabrics) 2. Push down outer ring to release pressure. (Heavy fabrics) 3. Insufficient pressure may cause poor feeding, skipped stitches, or difficulty in guiding the fabric.
FABRIC THREAD NEEDLE TABLE TO START SEWING Please note that the following list is a guide when sewing different fabrics. Important Hints 1. Raise the takeup lever to its highest position before starting and after stopping sewing. 2. Hold both threads about 10 cms to the rear of machine for the first two or three stitches.
TO FINISH SEAM 1 .Sew to the edge of seam. 2.Push the reverse button and sew in reverse ‘for about 3-4 cms. 3.Raise needle to its highest position. 4.Lift presser foot and pulloul the fabric to rear of machine. STRAIGHT STITCH 1 This type of stitching is the one used most frequently.
BLflTON SEWING 1 .Lower drop feed. 2. Place button attaching presser foot in position. 3.Place button between presser foot and fabric and lower presser foot. 4.Manually turn hand wheel towards you ensuring that the needle enters into both holes of button wfthout obstruction.
HEMMING Note: Hemmer foot can be purchased separately. 1. Raise the foot and the needle to its highest position. Replace the toot with the hemmer foot. 2. Fold over the fabric edge by about 3mm and place it under the foot. Secure the folded edge with a few stitches.
QUILTER Note: Quilt guide can be purchased separately. BUTTONHOLE SEWING 1.MARK WITH A PENCIL OR CHALK THE EXACT LENGTH OF THE BUTTONHOLE ON THE FABRIC. 2. REMOVE THE REGULAR PRESSER FOOT AND ATTACH THE BUTTONHOLE FOOT & PUT THE FAE UNDER ThE BUTTONHOLE FOOT.
9 U’ 5. .4 “I C, .4 CD C. 0 C z C. CD C. CD 0 -4. C. CD C. 0 CD CD C) CD DC CD CD CD C. 0. 0 CD 0 CD .4 0 ‘C 0 ‘C CD DC 0. 0 0 z ‘a, 0. DC r CD p. (fl Cl) r’ T DC 3’ .4 ,.4 ,- In -‘ .4 0 CD 0 . o 0 CD o , .C CD CD — DC DC C DC DC DC • ‘ CD CD (V DC 0 0 - 0 ‘2: .
デバイスPfaff hobby 1010の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pfaff hobby 1010をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPfaff hobby 1010の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pfaff hobby 1010の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pfaff hobby 1010で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pfaff hobby 1010を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPfaff hobby 1010の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pfaff hobby 1010に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPfaff hobby 1010デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。