ACDelcoメーカーPN 09301 Aの使用説明書/サービス説明書
ページ先へ移動 of 22
Manual Page 1 Pressure Washers and Accessories KING BRUTE ( PN 09301 A ) Operators Manual and Parts Lists Delco Pressure Washers LIT-KING-DEL Re v1 1 1- 07.
L I M I T E D W A R R A N T Y At DELCO ® CLEANING SYSTEMS, we distribute top quality industrial / commercial / personal pressure washers that are designed for heavy-duty use, maximum reliability, durability, and long life. Our pressure washers are built for all duty applications and steady use due to higher quality levels.
L I M I T E D W A R R A N T Y ( c o n t ) Parts / Co m ponents Warranty Period and Deta il s High Pressure Pumps Five (5 ) year limited manufactuer warranty on pu m p workmanship and defects in material.
Manual Page 4 IMPORTANT SAFETY PRECAUTIONS IMPORTANT: Please read the following instructions before installing and operating this equipment. DANGER THIS EQUIPMENT CAN BE HAZA RDOUS TO OPERATOR SAFETY AND ONLY AUTHORIZED PERSONNEL WHO HAVE READ AND UNDE RSTAND T HE INSTALLATION AND OPERATION MANUAL SHOULD BE PERMITTED TO OPERATE T HIS EQUIPMENT.
Manual Page 5 14. Always cool down coil. DO NOT’S DO NOT - UNDER ANY CIRCUMSTANCES - POINT THE HIGH PRESSURE NOZZLE AT YOURSELF, OTHER PEOPLE, OR ANIMALS! 1. DO NOT use an undersized discharge nozzle. 2. DO NOT disconnect the pressure hoses or wand while the equipment is HOT, PRESSURIZED or RUNNING.
Manual Page 6 INSTALLATION 1. LOCATION Avoid operating units in small areas or near ex haust fans. A dequate oxygen is needed for combustion or dangerous carbon monoxide will result. Stationary units should be installed in accordance with local plumbing and heating codes.
Manual Page 7 OPERATING THE MACHINE PRE-OPERATING INSTRUCTIONS 1. Connect the swivel end of the discharge hose to the cleaning gun. 2. Attach the hose to the machine outlet. 3. Check the fuel level in the fuel tank. Add fuel if r equired. It is best to keep fuel tank full during nonworking conditions.
Manual Page 8 SHUT DOWN INSTRUCTIONS 1. If the burner is on turn control switch to position 1(pump). 2. Run water through the pump until cool water flows from the cleaning gun. Failure to do this cou ld result in increased coil scaling. 3. Turn the control switch to off.
Manual Page 9 MAINTENANCE OF COMPONENTS PUMPS 1. Refer to pump section in this manual for your model of equipment. 2. Change pump oil after the first 25 hours of use. Subsequent changes should be every 250 hours or 3 months, whichever comes first. A. Disconnect power supply.
Manual Page 10 6. FUEL PUMP: To bleed air out of fuel pump, open air bleed valve on side of fuel pump. Turn machine and burner ON. When fuel looks clear (NOT FOAMING), close air bleeding valve. Air is out of fuel lines and fuel pump. A. To check fuel pressure, plumb a 200 PSI gauge into the port marked gauge.
Manual Page 11 DE-SOOTING COIL Poor grades of fuel oil or inadequate combustion air will cau se heavy soot build up on the outside surface of the heating coil. This will insulate the coil and rest rict air flow through the coil, further aggravating the soot build up.
Manual Page 12 DIAGNOSIS AND MAINTENANCE PROBLEM PROBABLE CAUSE SOLUTION Low Pressure Worn nozzle Replace nozzle of proper size. Belt slippage. Tighten or replace; use correct belt. Air leak in inlet plumbing. Use PTFE liquid or tape. Pressure gauge inoperative or not registering accurately.
Manual Page 13 Notes:.
Repair Kits Pos Code Description Qty . 44 67 40 69 41 42 70 2 1 3 4 5 4 3 1 2 6 7 8 9 13 12 11 10 14 15 16 17 18 19 20 21 22 23 24 25 27 33 28 27 34 35 36 37 38 28 32 31 30 27 28 71 72 73 74 57 3 (6) .
PP A0015 Unloader Code Description Qty . Special Parts / Kits Repair Kits Pos Code Description Qty . Pos Code Description Qty . 15 19 14 17 12 6 11 13 16 18 20 21 22 23 24 1 2 3 4 5 7 8 10 9 Repair Ki.
Manual Page 1 6 BURNER (Beckett 12V) COMPONENT LOCATOR & PARTS LIST Ref.No. Part No. Qty. Description 1 29601A 1 Air Shutter 2 29602A 1 Air Band 3 29603A 1 Escutcheo n Plate 4 29604A 1 Gasket, Squ.
Manual Page 1 7 ELECTRICAL SCHEMATIC (12VDC).
Manual Page 1 8 GUNVALVE AND HOSE ASSEMBLY COMPONENT LOCATOR.
Manual Page 1 9 GUNVALVE AND HOSE ASSEMBLY COMPONENT LOCATOR PARTS LIST Ref. No. Qty . Part No. Description 1 1 QC-251-22 O-Ring / O-Anillo 2 1 QC-250-51 Female Socket, ¼ / Ancla Hembra, ¼ 3 1 GE-60.
Manual Page 20 GC 590-40 GUNVALVE COMPONENT LOCATOR.
Manual Page 2 1 GC 590-40 GUNVALVE COMPONENT LOCATOR PARTS LIST Ref. No. Qty. Part No. Description 1 1 GC-765-14 Housing (Right) / Carcasa (Derecho) 2 1 8001660 Housing (Left) / Carcasa (Izquierdo) 3 .
1111 E. Lake Francis Dr. • Siloam Springs, AR 72761 • 1-800-B UY-DELCO.
デバイスACDelco PN 09301 Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ACDelco PN 09301 Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはACDelco PN 09301 Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ACDelco PN 09301 Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ACDelco PN 09301 Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ACDelco PN 09301 Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はACDelco PN 09301 Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ACDelco PN 09301 Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちACDelco PN 09301 Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。