PioneerメーカーDVR-650H-Sの使用説明書/サービス説明書
ページ先へ移動 of 134
<VRB1464-A> Pr inted in China HDD/DVD Recorder DVR-650H-S Operating Instructions HDD/D VD RECORDER Operating Instructions P ublished by Pioneer Corporation . Copyright © 2007 P ioneer Corporation. All rights reser ved. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC.
Thank you for buying this P ioneer product. Please read through these operating instructions so you will know how to operate your model properly . After you have finished reading the instructions, put them away in a safe place for future reference.
CAUTION The ST ANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord ser ves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power .
4 En Contents 01 Before you start What’s in the box . . . . . . . . . . . . . . . . . . . 6 Putting the batteries in the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Using the remote control . . . . . . . . . . . . . . 6 Disc/content format playback compatibility .
5 En 07 Playing and recording from a DV camcorder Playing from a DV camcorder . . . . . . . . . 63 Recording from a DV camcorder . . . . . . . 63 About DV . . . . . . . . . . . . . . . . . . . . . . . . . 65 08 Editing Editing options . . . . . . . . .
Before you start 01 6 En Chapter 1 Before you start What’s in the box Please confirm that the following accessories are in the box when you open it: • Remote control • AA/R6P dry cell batteries .
Before you start 7 En 01 • You can control this recorder using the remote sensor of another Pioneer component via the CONTROL IN jack on the rear panel. See Rear panel connections on page 14 for more information. Disc/content format playback compatibility Compatible media • DVD-RW ver.
Before you start 01 8 En HDD/DVD Recording and playback compatibility This recorder can play and record all widely-used DVD disc types, and additionally provides HDD functionality. The table below shows some specific compatibility differences between the different disc types.
Before you start 9 En 01 Using DVD-R DL/DVD+R DL discs DVD-R DL (Dual-Layer) and DVD+R DL (Double-Layer) discs contain two recordable layers on a single side, giving about 1.8 times the recording capacity of a conventional single-layer disc. This unit can record to both DVD-R DL and DVD+R DL discs.
Before you start 01 10 En • Bit-rates: Any (128 kbps or higher recommended) • Variable bit-rate (VBR) MP3 playback: Yes • VBR WMA playback: No • WMA encoder compatibility: Windows Media Codec .
Before you start 11 En 01 DivX ® VOD content In order to play DivX VOD (video on demand) content on this recorder, you first need to register the recorder with your DivX VOD content provider. You do this by generating a DivX VOD registration code, which you submit to your provider.
Before you start 01 12 En About the internal hard disk drive The internal hard disk drive (HDD) is a fragile piece of equipment. When used without the proper care or in the wrong conditions, it is possible that recorded contents may be damaged or lost entirely, in some cases making even normal playback or recording impossible.
Before you start 13 En 01 Symbols used in this manual The following icons are provided to help you quickly identify which instructions you need for which kind of disc. HDD Any type of DVD disc (recordable or playback only), finalized or not. Commercially produced DVD, finalized Video mode DVD-R/-RW.
Connections 02 14 En Chapter 2 Connections Rear panel connections 1 ANTENNA IN (RF IN)/OUT Connect your TV antenna to the ANTENNA IN (RF IN) jack. The signal is passed through to the ANTENNA OUT jack for connection to your TV. 2 INPUT 3 Stereo analog audio, video and S-video inputs for connection to a satellite receiver, set top box, etc.
Connections 15 En 02 Front panel connections On the front panel there is a flip-down cover that hides more connections. Left side: 11 DV IN A DV input i.LINK connector, suitable for connecting a DV camcorder. 12 USB port (Type B) USB port for connecting a PictBridge- compatible printer or PC.
Connections 02 16 En Easy connections The setup described here is a basic configuration that allows you to record TV programmes on both this recorder and your VCR. When watching recordings from this recorder, set your TV to input 1; switch to input 2 to watch a video playing in the VCR.
Connections 17 En 02 Using other types of video output This recorder has standard (composite), S-video and component video outputs. The main difference between them is the quality of the picture. S-video delivers a better picture than composite video, while component video gives better picture quality still.
Connections 02 18 En Connecting to a cable box or satellite receiver (1) If you are using a cable box or satellite receiver with only a few scrambled channels, follow the setup on this page 1 . If many or all the channels are scrambled, we recommend using the setup on the following page.
Connections 19 En 02 Connecting to a cable box or satellite receiver (2) If many or all the channels you receive by cable or satellite are scrambled, we recommend using this setup. 1 Using the setup on this page you can: • Record any channel by selecting it on the cable box/satellite receiver.
Connections 02 20 En Connecting to an AV amplifier or receiver To enjoy multichannel surround sound you need to connect this recorder to an AV amp/ receiver using the digital coaxial output. In addition to the digital connection, we recommend also connecting using the stereo analog connection.
Connections 21 En 02 Connecting using HDMI If you have an HDMI or DVI-equipped 1 monitor or display 2 , you can connect it to this recorder using an HDMI cable (not supplied). The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio.
Connections 02 22 En HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround- sound audio.
Connections 23 En 02 • Even if you make child lock settings (see Preventing use of the recorder before a timer recording (child lock) on page 45), this unit can still be controlled by the remote of a connected plasma television.
Connections 02 24 En Connecting a USB device Using the USB ports on the front of the recorder you can connect USB devices such as digital cameras, printers, keyboards and PCs. Please also see the instructions that came with the device you want to connect before using.
Connections 25 En 02 Using a PC • Note that you can connect a PC to this device via USB to copy WMA and MP3 files. For more information, see Connect PC on page 87.
Controls and displays 03 26 En Chapter 3 Controls and displays Front panel 1 DivX indicator Lights when this recorder plays DivX video files. 2 HDD/DVD Press to switch between HDD and DVD for recording and playback. 3 COPY indicator Lights when copying is underway.
Controls and displays 27 En 03 Display 1 Lights during playback; blinks when playback is paused. 2 Lights when copying. 3 Lights during recording; blinks when recording is paused. 4P M Lights to indicate PM (after midday) for the clock display.
Controls and displays 03 28 En Remote control 1 ONE TOUCH COPY (page 78) Press to start One Touch Copy of the currently playing title to DVD or the HDD. 2 Remote control indicator Lights when setting up the remote control for use with a TV (page 127) and when setting the remote control mode (page 114).
Controls and displays 29 En 03 13 DISC NAVIGATOR (page 55, 67) / TOP MENU (page 52) Press to display the Disc Navigator screen, or the top menu if a DVD-Video or finalized DVD-R/-RW (Video) disc is loaded. 14 MENU (page 52) Press to display the disc menu if a DVD- Video disc is loaded.
Getting started 04 30 En Chapter 4 Getting started Switching on and setting up When you switch the recorder on for the first time, you can make several basic settings using the Setup Navigator feature. This takes you through setting the clock, the internal TV tuner and the video output.
Getting started 31 En 04 6 Select ‘Auto’ for automatic time setting, or ‘Manual’ to set the clock manually. • Auto clock setting Some TV channels broadcast time signals together with the programme. This recorder can use these signals to set the clock automatically.
Getting started 04 32 En 8 Select whether or not your TV is compatible with progressive scan video. • Note that progressive scan video is only output through the component video outputs and only when the video source is NTSC (see Using other types of video output on page 17).
Recording 33 En 05 Chapter 5 Recording About DVD recording This recorder can record to DVD-R, DVD- RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL and DVD+R DL media. DVD-R and DVD-RW discs can be initialized for Video mode or VR mode recording. Each has its advantages, and it depends on what you want to do with the recording which mode you choose.
Recording 05 34 En • If power to the recorder is cut (due to a power outage, the plug being pulled from the power outlet, etc.) during recording, editing, initializing, finalizing or other operation, some recorded material on the disc, or the disc itself, may become unusable.
Recording 35 En 05 selected as the broadcast audio channel, both the main and SAP channels are recorded and you can switch the audio on playback. Recorded audio In all except the LPCM mode, sound is recorded in two channel Dolby Digital format (only Dolby Digital 2.
Recording 05 36 En Using the built-in TV tuner There are three different ways to select TV channels. Note that you can’t change the TV channel during playback, recording or during recording standby. • CH +/– buttons • Number buttons For example, to select channel 4, press 4 then ENTER ; for channel 34, press 3 , 4 , ENTER .
Recording 37 En 05 • EP (Extended Play) – Lower quality than LP, but gives about six hours of recording time on a DVD disc. • SLP (Super Long Play) – Lower quality than EP, but gives about eight hours of recording time on a DVD disc.
Recording 05 38 En the front panel display. When the recording ends, the recorder automatically switches into standby if no other operation is being performed. • To cancel the set recording time, press REC . • If you want to pause recording at any time 1 , press PAUSE .
Recording 39 En 05 • Approximately two minutes before a timer recording is set to start, the recorder will go into timer recording standby. In timer recording standby you cannot use some functions. • The maximum length for timer recordings made to the HDD is 24 hours.
Recording 05 40 En 7 Move the cursor to the recording end time on the grid. As you move the cursor around the grid, an arrow stretches from the start time to the current cursor position, representing the length of the recording. A recording of up to six hours can be set.
Recording 41 En 05 Checking/editing timer recording settings You can check and/or edit the timer recording settings made by the VCR Plus+ system by selecting Details from the PlusCode# setting screen. 1 Select ‘Details’ from the PlusCode# setting screen.
Recording 05 42 En Setting a manual timer recording The timer recording screen you can see all the timer programmes already set, clear programmes and set up new ones.
Recording 43 En 05 Auto Replace Rec. – Automatically erases the previous daily or weekly recording when the next one is recorded. Genre – Select a record genre (for HDD recording only).
Recording 05 44 En Editing a timer programme You can change any of the settings in a timer programme before the recording is due to start. 1 Press TIMER REC. 2 Highlight the timer programme you want to change. 3 Press then select ‘Modify’ from the command menu panel.
Recording 45 En 05 5 Select ‘Store Programme’. 6 Press to exit the Timer Recording screen. Stopping a timer recording 1 Press during a timer recording.
Recording 05 46 En Simultaneous recording and playback (Chase Play) Chase Play allows you to watch a recording that is still in progress from the start, without having to wait until the recording has finished (i.e., playback is ‘chasing’ the recording).
Recording 47 En 05 • To watch video coming in via the DV input (front panel), select DV > DV Video Playback from the Home Menu (see also Playing from a DV camcorder on page 63). 3 Set the recording quality. • See Setting the picture quality/recording time on page 36 for detailed information.
Recording 05 48 En • To cancel Auto Start Recording once recording has already started, press REC for three seconds (this cancels Auto Start Recording, but recording continues), then STOP REC to stop recording. • You can also stop recording by pressing STOP REC then selecting Yes to confirm.
Recording 49 En 05 • DVD-R DL (Video mode) discs and DVD+R DL discs must be finalized in order to play in other recorders/players. Note however that some recorders/ players will not play even finalized dual- layer discs. 1 Load the disc you want to finalize.
Recording 05 50 En DVD+RW and DVD-RAM discs can also be initialized in order to erase the contents of the disc. Important • Initializing a DVD-RW, DVD+RW or DVD-RAM disc will erase everything recorded on it.
Playback 51 En 06 Chapter 6 Playback Introduction Most of the features described in this chapter make use of on-screen displays. Navigate these using the cursor buttons and ENTER . To go back one level from any screen, use the RETURN button. Remember also that the button guide at the bottom of every screen shows which buttons do what.
Playback 06 52 En Playing DVD discs The table below shows the basic playback controls for DVD-Video, and recordable DVD discs. Playing from the HDD The table below shows the basic playback controls when playing video recorded on the hard disk (HDD). P ress to start playback.
Playback 53 En 06 Playing CDs and WMA/MP3 discs The table below shows the basic playback controls for audio CDs 1 , and WMA/MP3 files. Playing Video CD/Super VCDs The table below shows the basic playback controls for Video CD/Super VCDs. Some discs feature Playback Control (PBC for short) menus.
Playback 06 54 En Playing DivX video files The table below shows the basic playback controls for DivX video files. P ress to skip to previous/next track. When a PBC menu is displayed, press to display the previous/next page. (During playback you can also use the front panel CH +/– buttons.
Playback 55 En 06 Using the Disc Navigator to browse the contents of a disc Use the Disc Navigator to browse the contents of a disc and start playback. Using the Disc Navigator with recordable discs and the HDD You can use the Disc Navigator to browse and edit video on recordable DVDs and the HDD, and to view information on titles.
Playback 06 56 En Using the Disc Navigator with playback-only discs 1 Display the Home Menu. 2 Select ‘Disc Navigator’. Alternatively, for a CD, Video CD, Super VCD or WMA/MP3/DivX disc, you can press DISC NAVIGATOR , which takes you straight to the Disc Navigator screen.
Playback 57 En 06 Frame advance/frame reverse You can advance or back up video on a DVD disc 1 or the HDD frame-by-frame. With Video CDs/Super VCDs and DivX titles, you can only use frame advance. 1 Pause playback. 2 Back up or advance one frame with each press.
Playback 06 58 En A-B Repeat The A-B Repeat function allows you to specify two points (A and B) within a track or title that form a loop which is played over and over. 1 1 During playback, select ‘A-B Repeat’ from the Play Mode menu. 2 With ‘A (Loop Start)’ highlighted, press at the point you want the loop to start.
Playback 59 En 06 The Input/Edit Programme screen varies according to the disc type. Below is the DVD input screen. 2 Select a title, chapter, folder or track for the current step in the programme list. After pressing ENTER to add the title/ chapter/folder/track, the step number automatically moves down one.
Playback 06 60 En Switching DVD and DivX soundtracks When playing a DVD disc or DivX title recorded with two or more soundtracks (often in different languages), you can switch the soundtrack during playback. 1 Check the disc packaging for details of the soundtrack options.
Playback 61 En 06 • Switch the camera angle. • The angle number is displayed on- screen. • If the disc was paused, playback starts again with the new angle. Displaying disc information on-screen You can display various on-screen information about the disc loaded or the HDD.
Playback 06 62 En Tip • See Switching camera angles on page 60 for more on multi-angle scene switching. • When using the simultaneous play and record feature, the display shows information for playback only. • During real-time copy, the copy source playback information is displayed.
Playing and recording from a DV camcorder 63 En 07 Chapter 7 Playing and recording from a DV camcorder You can play back and record video from a DV camcorder connected to the DV IN jack on the front panel of this recorder. Important • If you connect a second recorder using a DV cable, you cannot control the second unit from this one.
Playing and recording from a DV camcorder 07 64 En 1 Make sure your DV camcorder is connected to the front panel DV IN jack. Also, set the camcorder to VTR mode. 2 Set the recording quality. • See Setting the picture quality/recording time on page 36 for detailed information.
Playing and recording from a DV camcorder 65 En 07 5 Select ‘Record to Hard Disk Drive’ or ‘Record to DVD’. The DV tape is rewound to the beginning. Once it is rewound, the DV tape is played from the beginning and copied to either the HDD or a DVD.
Editing 08 66 En Chapter 8 Editing Editing options The table below shows which commands you can use with the HDD and different disc types. *1 DVD-R/-RW only HDD DVD-R/-RW (Video mode), DVD+R/+RW DVD-R.
Editing 67 En 08 The Disc Navigator screen The Disc Navigator screen is where you can edit video content on unfinalized Video mode and DVD-R/-RW (VR mode) discs, DVD+R/ +RW and DVD-RAM, as well as video content on the internal hard disk drive.
Editing 08 68 En HDD genres The large capacity of the HDD means that there may be many hours of video in the recorder. To help you organize your HDD video content you can assign different genres to titles. There are 10 genres in total, including ten user-definable ones that you can name as you like.
Editing 69 En 08 1 Highlight the title you want to erase. 2 Select ‘Erase’ from the command menu panel. 3 Select ‘Yes’ to confirm or ‘No’ to cancel. Tip • You can erase a title quickly by pressing CLEAR when the title is highlighted. Confirm the edit by pressing ENTER .
Editing 08 70 En Using the remote key shortcuts to input a name The table below shows the remote control key shortcuts that you can use to input characters in the name input screen.
Editing 71 En 08 Set Thumbnail You can change the thumbnail picture that appears in the Disc Navigator for a title to any frame that appears in that title. 1 Highlight the title you want to change the thumbnail picture for. 2 Select ‘Edit’ > ‘Set Thumbnail’ from the command menu panel.
Editing 08 72 En 5 Highlight ‘To’ then, in the same way, find the end of the section to erase, then press ENTER. After pressing ENTER , another marker indicates the end of the section, with the section itself marked in red. 6 Select ‘Yes’ to confirm, or ‘No’ to cancel.
Editing 73 En 08 • For more information about these options, see Editing accuracy on page 67. 4 Select the command you want: • Divide – Divide a chapter into two or more parts: Use the playback controls ( , , , , etc.) to find the point at which you want to divide the chapter, then press ENTER .
Editing 08 74 En 3 Select a genre for the title. Lock Original only You can lock a title so that it can’t be edited or erased accidently. If you do need to edit it, you can always unlock it later. Important • You can’t undo any edits made before changing the lock status.
Editing 75 En 08 Combine Play List only Use this function to combine two Play List titles into one. 1 Highlight the title you want to combine. This title will remain in the same place after combining with another title. 2 Select ‘Edit’ > ‘Combine’ from the command menu panel.
Editing 08 76 En • For information on remote control key short cuts, see Using the remote key shortcuts to input a name on page 70. 4 Select ‘OK’ to enter the name and exit. Multi-Mode Multi-Mode allows you to select several titles, then select a command that will be applied to all of them.
Editing 77 En 08 Frequently asked questions • Why doesn’t the available recording time increase when I erase titles from a VR mode DVD-R? When you erase titles from a DVD-R (or DVD+R), the titles are no longer displayed, but the content remains on the disc.
Copying and backup 09 78 En Chapter 9 Copying and backup Introduction Use the copying features of this recorder to: • Back up important recordings stored on the HDD to a DVD. • Make a DVD copy of a recording on the HDD to play in another player. • Transfer video from a DVD to the HDD for editing.
Copying and backup 79 En 09 HDD to DVD copies are made in the same recording mode. When copying DVD to HDD, the copy is made in whatever recording mode is currently set. Make sure that a recordable DVD disc is loaded when trying to copy from the HDD. 1 If you’re copying from DVD to the HDD, select a recording mode.
Copying and backup 09 80 En • Thumbnail picture markers and chapter markers for the Disc Navigator are copied, but their position in the copy may be slightly changed from the original. • If some part of the title being copied is copy-protected, copying will start, but the copy-protected portions will not be copied.
Copying and backup 81 En 09 There are some restrictions on titles that can be added to the Copy List if you are copying to a DVD-R/-RW (Video mode) or DVD+R/ +RW: • When adding titles that contain copy- once protected material, the copy-once parts will not be added.
Copying and backup 09 82 En • Set Thumbnail – Set the thumbnail frame for a title (see Set Thumbnail on page 71). • Recording Mode – Set the picture quality of the copy (see Recording Mode on page 83).
Copying and backup 83 En 09 – the recorder is reset to its factory settings (see Resetting the recorder on page 131). • It may not be possible to copy from a DVD disc that was recorded on a different DVD recorder or a PC. 1 Select ‘Copy’ from the Home Menu.
Copying and backup 09 84 En • Optimized 1,2 – The recording quality is automatically adjusted so that the Copy List fits on to the space available on the disc. Copying is carried out in real-time. When you change the recording mode setting, you can see how much disc space it will require.
Copying and backup 85 En 09 • You can cancel the backup process by pressing ONE TOUCH COPY for more than one second. 5 When the data has been copied, take out the disc and load a blank* recordable DVD.
Using the Jukebox 10 86 En Chapter 10 Using the Jukebox The Jukebox feature allows you to use the recorder’s HDD to store and playback music from up to 999 of your CDs. You can also transfer WMA/MP3 files stored on CD-R/-RW/ -ROM, DVD, USB device or PC.
Using the Jukebox 87 En 10 • Up to 99 folders/999 files on the USB device can be copied/displayed. Connect PC Using a USB connection, you can copy WMA and MP3 files from a PC to the HDD of this device. Operations carried out on the PC require Windows Media Player 10.
Using the Jukebox 10 88 En 6 Open Windows Media Player 10 on the PC. The device settings screen appears. Click ‘Cancel’. *Depending on the settings for Windows Media Player 10, the screen shown below may not be displayed. From the PC, in Windows Media Player 10: 1.
Using the Jukebox 89 En 10 • Folders containing no files are not displayed in the Jukebox (such as the above ‘Artist1’ and ‘Artist2’ folders), but do count toward the maximum of 999 folders allowed in Jukebox. • Up to 999 tracks can be included in one album.
Using the Jukebox 10 90 En Changing the album view 1 From the album list, display the view options menu panel. 2 Select a view option. • Sort order By number – Albums are listed by the album number. By favourite – Most often listened to music appears at the top of the list.
The PhotoViewer 91 En 11 Chapter 11 The PhotoViewer From the PhotoViewer you can view JPEG photos and picture files stored on the HDD, recordable DVD or CD-R/-RW/-ROM, or on a USB-equipped digital camera. 1 You can also import files and save them to the recorder’s HDD or a DVD-R/-RW disc.
The PhotoViewer 11 92 En • You can change folders via the REV SCAN / FWD SCAN buttons. • If you encounter a disc that will not play, check that the disc and file formats are compatible with this recorder (see JPEG file compatibility and PC-created disc compatibility on page 11).
The PhotoViewer 93 En 11 Zooming an image During a slideshow you can zoom in to enlarge a portion of the picture by a factor of two or four. You can also move the area of the picture displayed. 1 Press during the slideshow to zoom the picture. Repeated presses cycle between zoom off, 2x zoom and 4x zoom.
The PhotoViewer 11 94 En • Importing to the HDD will not work if there is insufficient space on the HDD, or if there are already the maximum number of files and/or folders on the HDD (999 folders/999 files per folder). Selecting multiple files or folders The Multi-Mode allows you to select multiple folders/files at once for importing or editing.
The PhotoViewer 95 En 11 Important • Use a blank DVD-R/-RW disc, or one that has already been initialized for Video mode recording but has nothing yet recorded on it. Discs that have already been recorded on (as well as CD-R/-RW discs) cannot be used.
The PhotoViewer 11 96 En Editing files on the HDD There are a number of commands you can use to edit and organize your pictures stored on the HDD. Creating a new folder 1 From the folder list, display the menu. 2 Select ‘New Folder’. The folder appears at the bottom of the folder list with the name F_ number .
The PhotoViewer 97 En 11 2 Display the command menu. 3 Select ‘File Options’ or ‘Folder Options’. 4 Select ‘Copy’ or ‘Copy Folder Contents’. 5 Select a folder to copy the folder(s)/file(s) to. 6 Select ‘Yes’ to confirm, or ‘No’ to cancel.
The PhotoViewer 11 98 En 4 Select ‘Lock’ or ‘Lock Folder Contents’. Locked files are shown with a padlock icon next to them. To remove all locks within a given folder, choose ‘Folder Option’ > ‘Unlock Folder Contents’ .
The Disc Setup menu 99 En 12 Chapter 12 The Disc Setup menu From the Disc Setup menu you can name discs, lock the contents to prevent accidental recording and erasure, initialize and finalize discs.
The Disc Setup menu 12 100 En Initialize settings You can initialize a recordable DVD-R/-RW disc for either VR mode or Video mode recording. The first time you load a new DVD-RW disc, it will be automatically initialized for recording according to the DVD-RW Auto Init.
The Disc Setup menu 101 En 12 1 Select ‘Disc Setup’ from the Home Menu. 2 Select ‘Optimize HDD’ then ‘Start’. A progress bar indicates how long there is left to go. If no actions are carried out for more than 20 minutes after the optimization process is completed, the unit turns itself off.
The Video Adjust menu 13 102 En Chapter 13 The Video Adjust menu Using the Video Adjust menu you can set up the picture quality for the built-in tuner and external inputs, for disc playback, and for recording.
The Video Adjust menu 103 En 13 • 3-D Y/C – Adjusts the brightness/colour separation. • YNR – Adjusts the amount of noise reduction (NR) applied to the Y (brightness) component. • CNR – Adjusts the amount of noise reduction (NR) applied to the C (colour) component.
The Video Adjust menu 13 104 En Creating your own set There are three user presets in which you can save your own set of picture quality settings for disc playback. 1 Follow Choosing a preset above and select one of the user presets (Memory 1, 2 or 3).
The Initial Setup menu 105 En 14 Chapter 14 The Initial Setup menu Using the Initial Setup menu The Initial Setup menu is where you can set various recorder options for sound, picture, language and so on. Some settings can only be changed when the recorder is stopped.
The Initial Setup menu 14 106 En Manual CH Setting Next Screen Proceed to the next screen if you need to adjust any of the settings made by auto tuning. Select your countr y , then proceed to the manual channel setting screen: • Change channel presets using the PREV / NEXT buttons.
The Initial Setup menu 107 En 14 Audio In External Audio Stereo • Select if the audio from the currently selected external input is standard stereo. Dual Mono Select if each channel carries a separate soundtrack.
The Initial Setup menu 14 108 En MPEG Out MPEG Output an MPEG audio signal when a source using MPEG audio is being played. MPEG PCM • Convert sources with MPEG audio to Linear PCM output. Use if your connected equipment doesn’t have an MPEG audio decoder .
The Initial Setup menu 109 En 14 Auto Language On • On this setting: • DVD-V ideo discs whose main audio track is in your default language will play using that language, without subtitles.
The Initial Setup menu 14 110 En Optimized Rec On The recording quality of timer recordings is automatically adjusted to fit on to the selected media if it will not fit at the selected quality setting. If the recording will not fit even at MN1 ( MN4 for DVD+R/ +RW), then the recording will be made to the HDD in the original quality selected.
The Initial Setup menu 111 En 14 HDD Recording Format Video Mode Off Recordings made to the HDD are made in VR mode. Use this setting if you don’t need to transfer the recording later to a DVD-R/-RW (Video mode) or DVD+R/+RW . Video Mode On • Recordings made to the HDD are compatible with Video mode recordings.
The Initial Setup menu 14 112 En Parental Lock Set Password In order to change the parental lock level or change the countr y/area code, set the password using this option. F rom the following screen, enter a four-digit number that will be your password.
The Initial Setup menu 113 En 14 Colour RGB (0–255) Use if colours are weak and black appears to ‘ float’ on the RGB (16–235) setting. RGB (16–235) Use this setting if colours appear overly rich and the black too deep on the RGB (0–255) setting.
The Initial Setup menu 14 114 En Additional information about the TV system settings About the input line system This recorder is compatible with PAL-N, 3.58 NTSC and PAL-M TV systems. The Input Line System and Input Colour System settings determine how the recorder treats incoming video signals from an external input or the built-in TV tuner.
The Initial Setup menu 115 En 14 pressing INPUT SELECT (also front panel) while the recorder is stopped. • When you switch the Input Line System setting the Copy List is erased. If you switch the setting using the (Stop) button and INPUT SELECT buttons as described above, there is no confirmation, so please use with care.
Additional information 15 116 En Chapter 15 Additional information Minimum copying times The table below shows the minimum HDD to DVD copying time for one hour of video. Please note that not all discs are compatible with high-speed copying. 1 Check with the disc manufacturer for compatibility.
Additional information 117 En 15 Manual recording modes The table below shows the approximate recording times for different DVD types in each manual recording mode, as well as the standard recording mode equivalents. For recording time on the HDD, see Specifications on page 132.
Additional information 15 118 En • Levels separated by a bold line show where there is a noticeable change in picture quality. • Audio recording in all manual recording modes is in Dolby Digital 2 ch format, except for LPCM mode, which is in Linear PCM format.
Additional information 119 En 15 All settings are r eset • If the recorder is unplugged (or there is a power failure) while the recorder is on, all the settings will be lost. • Make sure that you switch the recorder into standby before unplugging the power cord.
Additional information 15 120 En Can’t play a disc recor ded using this recor der on another player • If the disc was recorded in DVD-R/-RW (Video mode) or DVD+R , make sure that it’s finalized (page 48). • Some players will not play recordable DVD discs, even when recorded in DVD-R/-RW (Video mode) or DVD+R and finalized.
Additional information 121 En 15 After briefly unplugging or after a power failure the fr ont panel display shows ‘--:--’ •A backup batter y inside the recorder keeps the clock and other settings from being reset when there is no power to the recorder .
Additional information 15 122 En HDMI Problem Remedy The connected HDMI or DVI device does not display any picture (and the front panel HDMI indicator does not light) •T ry disconnecting then reconnecting the HDMI cable (while the power of both components is on).
Additional information 123 En 15 If the unit does not operate normally due to external effects such as static electricity, disconnect the power plug from the outlet and insert again to return to normal operating conditions.
Additional information 15 124 En On-screen displays The table below shows a list of error messages that you may encounter when using the recorder and an explanation of their meaning. Message Explanation/Action • Initializing disc. Please wait a moment.
Additional information 125 En 15 • Repairing disc. • Repairing the HDD. During recording, the power was cut. This display appears when the power is restored. • Could not repair the disc. The recorder was unable to repair the disc after a power cut.
Additional information 15 126 En Front-panel displays The table below shows a list of error messages that you may encounter when using the recorder and an explanation of their meaning. • There is no DV input or the input signal is unrecor dable. No signal was detected at the DV IN jack.
Additional information 127 En 15 Setting up the remote to control your TV You can use the supplied remote to control your TV. To be able to use this feature you first have to program the remote with a maker code from the table below. 1 Press and hold down the CLEAR button, then enter the maker code for your TV.
Additional information 15 128 En Language code list Language (Language code letter), Language code Country/Area code list Country/Area, Country/Area code , Code letter Japanese (ja), 1001 English (en).
Additional information 129 En 15 Screen sizes and disc formats When viewing on a standard TV or monitor Screen format of disc Setting Appearance 16:9 4:3 (Letter Box) The programme is shown in widescreen with black bars at the top and bottom of the screen.
Additional information 15 130 En Handling discs When holding discs of any type, take care not to leave fingerprints, dirt or scratches on the disc surface. Hold the disc by its edge or by the center hole and edge. Damaged or dirty discs can affect playback and recording performance.
Additional information 131 En 15 Hints on installation We want you to enjoy using this unit for years to come, so please bear in mind the following points when choosing a suitable location for it: Do... Use in a well-ventilated room. Place on a solid, flat, level surface, such as a table, shelf or stereo rack.
Additional information 15 132 En Specifications General Power requirements . . . . . . . . . . . . . . . . . . . . . 110 V to 240 V, 50 Hz / 60 Hz Power consumption . . . . . . . . . . . . . . . . . . . . . . . .48 W Power consumption in standby mode .
Additional information 133 En 15 Input/Output VHF/UHF antenna input/output terminal . . . . . . . . . . . . VHF/UHF set 75 Ω (F-shape connector) Video input . . . . . . . . . . Input 1, 3 (rear), Input 2 (front) Input level . . . . . . . . . . . . .
<VRB1464-A> Pr inted in China HDD/DVD Recorder DVR-650H-S Operating Instructions HDD/D VD RECORDER Operating Instructions P ublished by Pioneer Corporation . Copyright © 2007 P ioneer Corporation. All rights reser ved. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC.
デバイスPioneer DVR-650H-Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Pioneer DVR-650H-Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPioneer DVR-650H-Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pioneer DVR-650H-Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pioneer DVR-650H-Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pioneer DVR-650H-Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPioneer DVR-650H-Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pioneer DVR-650H-Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPioneer DVR-650H-Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
