PioneerメーカーPRV-LX1の使用説明書/サービス説明書
ページ先へ移動 of 20
PRV-LX1 RS-422A Command Protocol Manual March 2005 Version 3.02 TP #T502201 All Rights Reserved Table of Contents 1.0 F OREWORD .................................................................................. 2 2.0 C OMMUNICATION S IGNAL ...........
PRV-LX1 RS-422A Protocol 7.0 P ROCEDURE FOR I SSUING C OMMAND ........................................... 14 8.0 P RODUCT -S PECIFIC N OTES ......................................................... 16 8.1 Recording Delay ..............................
PRV-LX1 RS-422A Protocol 1.0 Foreword The PRV-LX1 can be controlled externa lly using RS-422A commands. Control is applied through the REMOTE IN and REMOTE OUT D-Sub 9 con nector on the rear panel. Set the RS-422A REMOTE controls through the main menu.
PRV-LX1 RS-422A Protocol 2.0 Communication Signal The PRV-LX1 conforms to EIA RS-422A and incl ude s a full duplex communication channel. The tran sfe r speed is 38.4kb per second. Data Format: Start Bit: 1 bit Data: 8 bits Parity (ODD): 1 bit Stop Bit: 1 bit 3.
PRV-LX1 RS-422A Protocol 4.0 Command Block Format The controlling device and the PRV-LX1 communicate through the interchange of command blocks. The bytes in each command block are assig ned as follows.
PRV-LX1 RS-422A Protocol The controller must ensure that no more than a 10 msec lap se occurs between b y tes in a command block. The controller must immediately stop sending data when it receives a NAK + Error Data message. The unit must wait at least 10 msec before resending the comman d.
PRV-LX1 RS-422A Protocol 5.0 Command Table Code Command Response 00 11 Device Type Request 12 11 xx xx Device Type 20 00 Stop 10.01 ACK 20 01 Play 10 01 ACK 20 02 Rec(ord) 10 01 ACK 20 04 Standby OFF .
PRV-LX1 RS-422A Protocol 6.0 Command Formats 00 11 Device Type Request PRV-LX1 Responds with a 12 11 Device Type Message co ntaining 2 bytes of data TV System DATA 1 DATA2 NTSC F0 51 PAL F1 51 10 01 A.
PRV-LX1 RS-422A Protocol 20 20 Rewind During playback or Time Shift PLAY, this co mmand executes 192x speed Scan Reverse then pauses playback at the beginning of the title.
PRV-LX1 RS-422A Protocol 24 31 Cue Up With Data Cues the PRV-LX1 to the indicated time code and pauses. DATA – 1 DATA – 2 DATA – 3 DATA – 4 10 Frames 1 Frame 10 Seconds 1 Second 10 Minutes 1 Minute 10 Hours 1 Hour MSD LSD MSD LSD MSD LSD MSD LSD 44 14 In Data Preset Preset the value from DATA-1 to DATA-4 to the memory.
PRV-LX1 RS-422A Protocol 7X 20 Status Data Return all or part of the following data that co rresponds to the “61:2 0 Status Sen se ” com mand Data # MSB Bit – 7 Bit – 6 Bit – 5 Bit – 4 Bit.
PRV-LX1 RS-422A Protocol E2 51 21 Chapter Search (PRV-LX1 original command) The command searches to a recorded chapter number Values are 1-99 (0x01 – 0x99) DATA – 2 10 Chapters 1 Chapter MSD LSD Chapter number is given by DATA-2. Available chapter numbers are from 1 to 9 9.
PRV-LX1 RS-422A Protocol E3 51 72 Trimming Title Preset (PRV-LX1 origin al command) The command presets the trimming title number. Values are 1-255 (0x01 0x00 – 0x55 0x 02) Trimming title number executed by ”E1:51: 75 Trimming” command is specified by DATA-2, DATA-3, and the title number preset in the memory .
PRV-LX1 RS-422A Protocol E2 51 9F Mode Data When the unit receives the ”E1:51:8F Mode Sens e” command, the current status of the unit is reported as the value of DATA-2.
PRV-LX1 RS-422A Protocol 7.0 Procedure for Issuing Command <Example 1> < Example 1> is an example of playing Titl e 2, from the scene10m inutes to 20minutes “Drive Select” and “Selecting the project” are not possi ble to be remotely controlled.
PRV-LX1 RS-422A Protocol STAR T 20・ 02 Re c 61・ 20 S t at us S ense R ec ? N EN D E1 ・ 51・ 81 Ti tl e N um ber S ens e Ti tl e = 3 E3 ・ 51・ 11・ 02・ 00 Ti tl e S ea r ch 61・ 20 S t at.
PRV-LX1 RS-422A Protocol 8.0 Product-Specific Notes 8.1 Recording Delay There is a short delay of approximately 29+/-2 fr ames between when the PRV-L X 1 is issue d a record command and the comma nd is executed.
PRV-LX1 RS-422A Protocol 8.2 Playback Delay When the PRV-LX1 is issued a play command, it experiences up to a +2 frame s delay in the execution of the command.
PRV-LX1 RS-422A Protocol 9.0 Appendix Command Matrix by System Version Commands 2.04/1.03 2.51/1.03 ≥ 3.00/1.04 00 11 Device Type X X X 20.00 Stop X X X 20.01 Play X X X 20.02 Rec(ord) X X X 20.04 Standby OFF X 20.05 Standby ON X 20.0F Eject X X X 20.
PRV-LX1 RS-422A Protocol Manual Pioneer Electronics (USA) Inc. Industrial Solutions Business (ISB) 2265 East 220 th Street Long Beach, CA 90810 (310) 952 – 2000 Published by Pioneer Ele ctronics Cop.
デバイスPioneer PRV-LX1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Pioneer PRV-LX1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPioneer PRV-LX1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Pioneer PRV-LX1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Pioneer PRV-LX1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Pioneer PRV-LX1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPioneer PRV-LX1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Pioneer PRV-LX1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPioneer PRV-LX1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。