AtlonaメーカーAT-HD44M-SRの使用説明書/サービス説明書
ページ先へ移動 of 19
A tl onA 4x4 HDMI over C A T5 Ma trix with IR Control P a th A T-HD44M-SR User Manu al.
T ABLE OF CONTENTS 1. Introduction .................................................. 1 2. Features .................................................. 1 3. Specication .................................................. 2 4. Package Contents .......
INTRODUCTION 1 The A T -HD44M-SR 4x4 HDMI over CA T5 Matrix with IR Control Path provides the most exible and cost effective solution in the market to route high denition video sources plus multi-chan - nel (up to 7.1-channel) digital audio from any of the four HDMI sources to the remote displays at the same time.
SPECIFICA TIONS T echnical A T -HD44M-S A T -HD44M-R Role of usage T rue 4x4 matrix & transmitter [TX] Receiver [RX] HDMI compliance HDMI 1.2a HDCP compliance Y es Video bandwidth Single-link 165MHz [4.95Gbps] Video support 480i / 480p / 720p / 1080i / 1080p60 Audio support Surround sound (up to 7.
2 3 1. 1x A T -HD44M-S 2. 1x IR emitter cable 1 3. 2x Rack-mounting ears 4. 1x IR remote 1 5. 1x User Manual 6. 4x A T -HD44M-R 7. 4x IR receiver cable 8. 8x W all-mounting screws 9. 1x 5V 6A power adapter 1 Additional IR remote control and IR emitter cable can be purchased as optional accessories to control the HDMI sources located separately .
A T -HD44M-S Front Panel 1. Power: Power indicator LED 2. IR: IR receiver 3. Input: Input source indicator LED 4. HP1–HP4: Connection status indicator LED for each output channel 5. Port1–Port4: Input source channels mapping LED for each output channel 6.
4 5 A T -HD44M-R Front Panel IN: Push button for switching input source channel in sequential order 1. EQ: Adjust the 8-level equalization control for HDMI signals. 0 – 7 = strongest – weakest. It is recommended to switch from 7 to 0 to nd the optimal visual experience.
DIP SWITCH SW1-SW4 for EDID/Audio DIP Switch Position Video Audio Description Pin#1 Pin#2 OFF OFF 1080p Stereo 1 Default Mode 2 – 1080p & stereo audio output for most HDTVs OFF ON 720p 1080i Ste.
6 IR Cables IR Emitter Cable IR Receiver Cable IR Sockets A T -HD44M-S IR Main: The default location for IR emitter extension cable to transmit all IR command signals received from any of the four remote receivers to all of the HDMI sources.
Supported IR Data Format Data Format Suitable Not Recommended NEC + RC5 + TOSHIBA MICOM CODE + GRUNDIG CODE + SONY 12 BIT CODE + SONY 15 BIT CODE + SONY 20 BIT CODE + RCA CODE + RCM CODE + MA TSUSHIT .
8 9 A T -HD44M-S as master: 1. Connect all sources to HDMI Inputs on the 4x4 HDMI over CA T5 matrix master A T -HD44M-S 2. Connect each DDC output on the A T -HD44M-S to respective DDC input on the remote re- ceiver A T -HD44M-R 3. Connect each TMDS output on the A T -HD44M-S to respective TMDS input on the remote receiver A T -HD44M-R 4.
OPER A TION and IR CONTROL Source Side Method A: Push Button Push the switch button on the front panel, the source will be sequentially changed. Method B: IR Remote Control a. Please press to enter IR control mode Note: If A T -HD44M-S receives the IR commands, the LED will ash.
10 1 1 Display Side Method A: Push button Push the switch buttons of respective output channels then the output channel will switch from HDMI source 1 to source 4 in sequential order , and wait a few seconds for audio/video of next channel coming out after the channel switch command is sent.
RS-232 SERIAL PORT CONTROL RS-232 transmission Format Bit Rate: 9600 Data Bits: 8 Parity: None Stop bits: 1 Flow Control: None Set Command The command set includes: A1~A4 setup the output of HP1 B1~B4 setup the output of HP2 C1~C4 setup the output of HP3 D1~D4 setup the output of HP4 VR send back rmware version => V3.
FIRMW ARE UPDA TE 13 W arning! There could be unexpected consequences resulted from inappropriate firmware update operation. Please do it with caution.
7. Please make sure your PC has direct connection to the RS-232 port of the MA TRIX, as shown in the picture (left), that in [Communication Setting] the onlne status should be “W ait to connect”. If the RS-232 connection is not firmly established, you will see the online status is “Disconnect.
NOTICE 14 15 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI/HDMI EDID information. 2. All HDMI over CA T5 transmission distances are measured using Belden 1583A CA T5e 125MHz LAN cable and ASTRODESIGN Video Signal Generator VG-859C.
SAFETY INFORMA TION 16 Safeguards T o reduce the risk of electric shock, do not expose this product to rain or moisture. If the wall plug does not t into your local power socket, hire an electrician to replace your obsolete socket. Do not modify the wall plug.
16 17 W ARR ANTY LIMITED ONE-YEAR W ARRANTY A TLONA by Lenexpo Electronics warrants only to the initial purchaser of this product for a period of one year from the date of purchase from an Authorized .
デバイスAtlona AT-HD44M-SRの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Atlona AT-HD44M-SRをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAtlona AT-HD44M-SRの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Atlona AT-HD44M-SRの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Atlona AT-HD44M-SRで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Atlona AT-HD44M-SRを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAtlona AT-HD44M-SRの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Atlona AT-HD44M-SRに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAtlona AT-HD44M-SRデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。