Planet TechnologyメーカーSW-501の使用説明書/サービス説明書
ページ先へ移動 of 20
.
T rademarks Copyright PLANET T echnology Corp. 2002. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET T echnology Corp.
- 2 - user ’ s guide, may cause harmful in terference to radio communications. Operation of this equipment in a re sidential area is likely to cause harm- ful interference, in which case the us er will be required to correct the in- terference at his own expense.
Table of Contents CHAPTER 1 IN TRODUCTION ................................................... 1 F AST E THERNET T ECHNOLOGY .................................................................. 1 S WITCHING T ECHNOLOGY ...................................
About This Manual Congratulations on your purchasing of SW-501/SW -801, 5/8-port 10/100Mbps Fast Ethernet Switch. This device integrates 100Mbps Fas t Ethernet and 10Mbps Ethernet net w ork capabilities in a highly flexible desktop package. Purpose This manual discusses how to install your SW-501/SW-801, 5/8-port 10/100Mbps Fast Ethernet Switch.
Overview of this User ’ s Manual Chapter 1, Introduction . Describes the Switch and its features. Chapter 2, Unpacking and Setup . Helps you get started with the basic installation of the Switch. Chapter 3, Identifying External Components . Describes the front panel rear panel and LED indicators of the Switch.
- 1 - Chapter 1 Introduction This chapter describes the features of the Switch and some background information about Ethernet/Fast Ethernet switching technology . Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks.
- 2 - segments. The switch, without interfering w ith any other segments, auto- matically forwards traffic that needs to go from one segment to another . By doing this the total network capacity is multiplied, w hile still maintaining the same network cabling and adapter cards.
- 3 - As all ports support 200Mbps, the Sw itches can be cascaded from an y port and to any number of switches. The Switches are a perfect choice for site planning to upgrade to Fast Ethernet in the future.
- 4 - Chapter 2 Unpacking and Setup This chapter provides unpacking and se tup information for the Switches. Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents.
- 5 - Chapter 3 Identifying External Components This section identifies all the majo r external components of the hub. Both the front and rear panels are shown followed by a description of each panel feature. The indicator panel is described in detail in the next chapter .
- 6 - DC Power Jack: Power is supplied through an external AC pow er adapter . Check the printing on the adapter for informa t ion about the AC power in- put voltage. Sin ce the switch does not includ e a power switch, plugging its power adapter into a pow er outlet will immediately power it on.
- 7 - Chapter 4 Connecting The Switch This chapter describes how to connect the Switch to your Fast Ethernet network. PC to Switch A PC can be connected to the Switch via a two-pair Catego ry 3, 4, 5 UTP/STP straight cable. The PC (equipped with a RJ-45 10/1 00Mbps phone jack) should be connected to any of the 5/8 numbered port.
- 8 - Switch to switches (other devices) The Switch can be connected to another switch or other devices (routers, bridges, etc.) via a two-pair Category 3, 4, 5 UTP/STP straight or crossover cable.
- 9 - Chapter 5 TECHNICAL SPECIFICATIONS Standards IEEE 802.3 10Ba se-T Ethernet IEEE 802.3u 100 Base-TX Fast Ether net Protocol CSMA/CD Data T ransfe r Rate Ethernet: 10Mbps (half duplex ), 20Mbps (full dup lex) Fast Ethernet: 100Mbps (hal f duplex), 200Mbps ( full duplex) T opology Star Network Cables 10BASET : 2-pair UTP Cat.
- 10 - Appendix A RJ-45 PIN Specification When connecting your 10/100Mbps Ethernet Switch to another switch, a bridge or a hub, a straight or crossover cable is necessary . Each port of the Switch supports auto-MDI/MDI-X detecti on. That means you can directly connect the Switch to any Ethernet devices without making a crossover cable.
- 1 1 - There are 8 wires on a standard UTP/S TP cable and each wire is color-coded. The following shows the pin allocation and color of str aight cable and crossover cable connection: Figure A-1: Str.
- 12 - Appendix B SWITCH OPERATION Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address infor- mation of some node in network, including MAC address, port no, etc.
- 13 - packet header , searches the rout ing t able provided for the incoming port and forwards the packet, only if required . The fast forwarding makes the switch attractive for connecting servers directly to the network, thereby increasing throughput and availability .
2010-000014-000.
デバイスPlanet Technology SW-501の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Planet Technology SW-501をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanet Technology SW-501の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planet Technology SW-501の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planet Technology SW-501で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planet Technology SW-501を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanet Technology SW-501の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planet Technology SW-501に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanet Technology SW-501デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
