PolaroidメーカーMicroCamの使用説明書/サービス説明書
ページ先へ移動 of 16
MicroCam User Guide (ENGLISH VERSION).
1 2 3 46 5 331 337 339 OI Am + – j a b c d e f h g i k n l m o.
1 3 39 + – 789 10 11 12 13 14 15 16 x 4.0 x 2.0 x 1.0 x .50 x .25.
17 18 19 20 21 22 23 6 OFF 2 3.5 4 n m p o a b c d e f g h i j l q k r.
Introduction The Polaroid MicroCam is designed to provide instant photographic capability to a wide variety of light microscopes. The camera is simple to operate, and is easily attached to the microscope’s viewing tube, in place of the eyepiece. (Note: The camera also can be attached to the phototube, if preferred.
The numbers throughout the text refer to the illustrations at the back of the book. The camera (Illustration 1) a Film holder b Film door latch c Control panel d Viewfinder e Microscope fitting f Remo.
The control panel (6) k Automatic/manual selector: Press to highlight the desired mode ( A utomatic/ m anual). l ON/OFF switch (O/l). m Film selector: Press repeatedly to high- light the correct film type (331/337/339). n Lighten/Darken control: This control is used to adjust the exposure before rephotographing the same subject.
Load the film 1 Release the latch to open the film door ( 7 ). Check that the steel developer rollers are clean before loading the film. Clean the rollers with a soft, lint-free cloth dampened with water, if necessary ( 8 ). Rotate both rollers as you clean and inspect them.
Operation 1 Place the specimen on the microscope focusing stage, and focus and frame the image. 2 Adjust the microscope illumination for photography; Koehler illumination is recommended for compound microscopes. If you are using neutral density filters over the light source when viewing, remove them before taking pictures.
Exposure too short or too long The camera will make aut o mat ic exposures as short as 1/60 second. If the microscope illumination is too bright, the camera will “beep” and the display will show: Place a neutral density filter over the microscope illuminator to increase the exposure time.
Xenon lighting If using a Xenon (daylight) microscope illuminator with color film, set the camera for Type 331 black & white film, to remove the built-in filter. Then press the black arrow ▼ to decrease the exposure by × .66 to comp ensate for the di ff er ence in film speed.
Microscope parts (17) a Phototube eyepiece b Phototube c Viewing eyepiece d Revolving nosepiece e Objective lens f Specimen g Specimen stage h Substage condenser i Aperture diaphragm adjustment j Cond.
4 Align the substage condenser by centering the image of the field diaphragm, using the condenser’s radial centering screws ( 21 ). If necessary, refocus the condenser once again, to keep the field diaphragm in sharp focus with the specimen image.
Possible problems and causes Vignetting (dark corners of print): Th e microscope may not be adjusted for Koehler illumination; the field diaphragm may not be opened far enough to fill the field of view. Image sharp only in center: May be due to incorrect objective lens for photomicrography.
FCC Notice (U.S.A. only) War ning: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
Polaroid Service Centers and Offices California Polaroid Corporation 3232 West MacArthur Boulevard P.O. Box 25200 Santa Ana 92799-5200 Tel: (714) 641-1200 Georgia Polaroid Corporation 5601 Fulton Industrial Blvd.
デバイスPolaroid MicroCamの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Polaroid MicroCamをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPolaroid MicroCamの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Polaroid MicroCamの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Polaroid MicroCamで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Polaroid MicroCamを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPolaroid MicroCamの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Polaroid MicroCamに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPolaroid MicroCamデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。