Polycomメーカー4400の使用説明書/サービス説明書
ページ先へ移動 of 23
VIEW Certified Configuration Guide Cisco 4400 Series Wireless LAN Controller (WLC), Wireless Integrated Serv ices Module (WiSM), and 3750G Integrated Wireless LAN Controller with 1100, 1130, 1200, 123.
Con fig ura tio n Gu ide Trademark Information Polycom® and t he logo designs SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registe red trademarks of Polycom, Inc. in the Un ited States of Am erica and various co untries. All other trademark s used herein are the propert y of their respective owners.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Introduction Polycom's Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is designed to ensure interoperability and high performance between SpectraLink Wireless Telephones and Wireless LAN infrastructure products.
Con fig ura tio n Gu ide Known Limitations • Wi-Fi Multimedia ( WMM ) must be disabled in order for SpectraLink Wireless Telephones to work properly. • Heavy multicast, broadcast, or push-to-talk ( PTT ) traffic may impair voice quality. • The Cisco 1000 series APs are not VIEW Certified at this time.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Network Topology The following configuration was tested during VIEW Certification. It is important to note that this configuration is not necessar ily applicable to all customer environments.
Con fig ura tio n Gu ide Configuring a New Controller Starting from Factory Defaults 1. Initial provisioning of the controller is done via the command line interface (CLI). Connect a null modem serial cable between the console port of the controller and the serial port of a PC.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Connecting to the Controller via a Browser 1. Connect to the WLC by pointing your internet browser to the URL: https<IP_Addr> (where <IP_Addr> is the IP address of the management interface of the WLC).
Con fig ura tio n Gu ide Installing Software 1. Make sure that the VIEW Certified version of software is installed on the controller. From the main menu, click Monitor . 2. In the navigation pane, click Summary. The heading labeled Software Version shows the current software version.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Controller Setup The initial setup of the controller is shown below. The setup instructions outlined in this document are for the configuration shown in the diagram only.
Con fig ura tio n Gu ide Connecting APs As the APs are connected to the ne t work, they should automatically find the controller via the LW APP discovery algorithms. The Dynamic Host Configuration Protocol (DHCP) server will assign each AP an IP address.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 4. Under DHCP Information, enter the IP address of the Primary DHCP Server. 5. Repeat this step for the ap-manager interface. 6. Click the Apply button and save the changes.
Con fig ura tio n Gu ide AP Configuration 1. Power-on and connect the APs to the network. Wait a few minutes for the APs to find the controller. 2. Verify the APs are associated to the WLC. 3. From the main menu, click Monitor. Configuration for SpectraLink Wireless Telephones running in 802.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 4. Set Admin Status to Enable . 5. Configure any other settings that might be relevant to your deployment as needed. 6. Click the Apply button to save all changes. 7. In the navigation pane under 802.
Con fig ura tio n Gu ide require the following minimum dBm reading to support the corresponding Mandatory data rate setting in the access point. 802.11 Radio Standard Minimum Available Signal Strength (RSSI) Maximum “Mandatory ” Data Rate -70 dBm 1 Mb/s 802.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 9. Use the default Fragmentation Threshold (2346 bytes). 10. Set the Beacon Period to 100.
Con fig ura tio n Gu ide Configuration for SpectraLink Wireless Telephones running in 802.11a mode 1. From the main menu, click Wireless. 2. In the navigation pane, under Access Points sele ct Radios , then select 802.11a /n. All the APs that are connected should be listed, showing their Operational Status as UP .
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 4. Set Admin Status to Enab le . 5. Configure any other settings that might be relevant to your deployment as needed. 6. Click the Apply button to save all changes. 7.
Con fig ura tio n Gu ide 10. Use the default Fragmentation Threshold (2346 bytes). 11. Set the Beacon Period to 100 . 12. Set DTIM Peri od to 2 . 13. SpectraLink Wireless Telephones do not support dynamic power and will not utilize the information element that is set when DTPC support is enabled.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 15. In the navigation pane under 802.11a/n, select EDCA Parameters. 16. Select Spectralink Voice Priority from the drop-down list. 17. Click the Apply button t o save the settings.
Con fig ura tio n Gu ide Setting Up the SSIDs It is required for voice and data to be on separate SSIDs to prioritize voice traffic. The voice SSID must be set to Platinum for Quality of Service (as shown in the screen shot below) and the data SSID must be set to Silver for Quality of Service .
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 5. Under the Profile Name heading, s elect the new Voice WLAN Profile. 6. Under the General tab , verify the Radio Policy corresponds to the SpectraLink Wireless Telephone configuration.
Con fig ura tio n Gu ide 8. Under the Security tab, select the desired security policy (either WPA or WPA2) and enter all required options. 9. Under the QoS tab, set Quality of Service to Platin um (voice ). (Note: This is the required setting for voice traffic.
Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Further Assistance 1. An installation and configuration guide for the 4400 WLC can be found on Cisco’s website: http://www.cisco.com/en/US/docs/wireless/controller/5.
デバイスPolycom 4400の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Polycom 4400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPolycom 4400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Polycom 4400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Polycom 4400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Polycom 4400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPolycom 4400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Polycom 4400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPolycom 4400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。