Porter-Cableメーカー28-306の使用説明書/サービス説明書
ページ先へ移動 of 20
14" Metal/W ood Cutting Band Saw Shown with Optional Stand and Optional Mobile Base Model 28-306 INSTRUCTION MANUAL P ART NO. 426-03-651-0011 - 06-03-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .
2 W oodworking can be dangerous if safe and pr oper operating procedur es are not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will con- siderably lessen the possibility of personal injury .
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUCT - TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly mini- mize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT .
4 ADDITIONAL SAFETY RULES FOR BAND SA WS 1. DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instruc- tions. 2. OBT AIN ADVICE from your supervisor, instruc- tor , or another qualified person if you are not familiar with the operation of this tool.
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be pr o - tected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wir e extension cords which have 3-pr ong ground- ing type plugs and matching receptacle which will accept the machine’ s plug.
6 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
7 ASSEMBL Y OPTIONAL ST AND The optional stand is shipped top-down in the shipping container with the motor mounted to the inside top of the stand. The on/off switch is wir ed to the end of the power cord. T o make the motor operational, do the following: 1.
8 A TT ACHING BEL T AND PULLEY GUARD, A TT ACHING AND ALIGNING V -BEL T , ADJUSTING BEL T TENSION DISCONNECT MACHINE FROM POWER SOURCE. 1. Use a straight edge to align the inside grooves of the pulleys (A) and (B) Fig. 9 to the inside edge of the drive pulley (C).
9 A TT ACHING THE SWITCH A push-button switch (mounted in a switch box) and a cord set ar e supplied with the unit. T o attach the switch to the band saw arm: DISCONNECT MACHINE FROM POWER SOURCE. The on/off switch-to-motor cor d (F) Fig. 11 is tied to the vertical mounting post (G) opposite the motor pulley .
10 Fig. 19 T ABLE INSER T Place the table insert (A) Fig. 19 in the hole provided in the table. Engage the protrusion on the insert in the indent (B) in the table. TIL TING THE T ABLE 1. The table on the machine can be tilted 45 degrees to the right and 10 degr ees to the left.
11 ADJUSTING BLADE TENSION A series of graduations is located on the back of the upper wheel slide bracket. These graduations indicate the proper tension for various widths of blades. With the blade on the wheels, turn the knob (A) Fig. 23 to raise or lower the wheel, until the re d fiber washer (D) Fig.
12 Fig. 30 Fig. 31 When using the machine for wood cutting (3000 SFM), pull the shifter knob (A) Fig. 30 all the way out so that the lugs of the clutch (B) are engaged with the hub (C) of the drive pulley . This action will disengage the clutch (D) from the hub (E) of the gear that transmits power through the gear box.
13 BEL T AND PULLEY ARRANGEMENTS FOR ALL EIGHT A V AILABLE SPEEDS With the longest belt on the inside groove of the motor pulley (B) Fig. 32 and on the drive pulley (C), and the small belt in one of t.
14 T rouble: BAND SA W DOES NOT COME UP TO SPEED. Pr obable Cause Remedy 1. Low voltage due to improper extension cord size. 1. Replace with adequate size cord. 2. Low voltage. 2. Contact an electrician. T rouble: BLADES BREAK. Pr obable Cause Remedy 1.
15 CUTTING CURVES When cutting curves, turn the stock carefully so that the blade may follow without being twisted. If a curve is so abrupt that repeated new kerfs ar e needed, then use either a narrower blade or one that has mor e set. The more set a blade has, the easier the stock is to turn.
16 BAND SAW BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. Y ou can obtain long use from a band saw blade if you use it properly . Be sure you use blades of the proper thickness, width, and temper for the various types of material and cuts.
17 LUBRICA TION The gear case is filled at the factory with 1-1/2 quarts of oil. The case should be drained after 1500 to 2000 hours of operation and filled with a good grade of heavy adhe- sive gear oil. A pipe plug is located underneath the machine in line with the gear pulley .
18 P ARTS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
19 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven t.
20 The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAM- MER ® , B.
デバイスPorter-Cable 28-306の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Porter-Cable 28-306をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 28-306の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 28-306の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 28-306で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 28-306を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 28-306の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 28-306に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 28-306デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
