Porter-Cableメーカー314の使用説明書/サービス説明書
ページ先へ移動 of 19
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage.
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm.
4 Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
ADDITIONAL SPECIFIC SAFETY RULES 6 a) Keep hands away from cutting area and the blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. b) Do not reach underneath the workpiece.
7 k) When restarting a saw in the workpiece, centre the saw blade in the kerf and check that saw teeth are not engaged into the material . If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted. l) Support large panels to minimize the risk of blade pinching and kickback.
8 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ...................
9 If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage.
10 NOTE: This tool is shipped completely assembled. No assembly time or tools are required. ASSEMBL Y OPERA TION SELECTING THE BLADE A combination blade is furnished with your saw and is an excellent blade for all general ripping and crosscutting operations.
11 TO ADJUST DEPTH OF CUT Loosen the depth adjusting knob (A) Fig. 1, and raise or lower the saw housing until the blade extends the desired distance below the base. For best results, the blade should barely protrude through the workpiece. Firmly tighten the knob to hold the saw in position.
12 Adjust the saw for the minimum depth of cut. Place the slot of the insert around the stud (A) Fig. 4 on the front of the saw base. Install a flat washer and thumb nut to the stud loosely. Adjust the saw for the desired depth of cut, and align the insert so that the saw blade is centered in the slot in the insert.
TO FOLLOW THE LINE OF CUT A notch is provided on the front edge of the base to assist in following the line of cut marked on the workpiece. The left edge of the notch (A) Fig. 7 is marked “45”. Use this edge to follow the line when making 45 degree bevel cuts.
14 RIPPING Ripping is cutting wood lengthwise. This operation is performed the same as crosscutting with the exception of supporting the workpiece. If the workpiece is supported on a large table, benc.
15 MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
16 Although all Porter-Cable tools have been thoroughly lubricated with a sufficient amount of high grade lubricant at the time of manufacture, check the oil level in the gear chamber before using your saw and periodically thereafter. To check the oil level: 1.
17 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier.
18 POR TER-CABLE LIMITED ONE YEAR W ARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.
デバイスPorter-Cable 314の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Porter-Cable 314をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 314の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 314の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 314で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 314を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 314の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 314に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 314デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。