Porter-Cableメーカー324MAGの使用説明書/サービス説明書
ページ先へ移動 of 15
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
2 SAFETY GUIDELINES - DEFINITIONS indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury.
3 3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts.
4 ADDITIONAL SPECIFIC SAFETY RULES SERVICE 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a tool, use only identical replacement parts.
5 z When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.
6 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section.
7 Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft.
2. While pressing the arbor lock button, extend the lever on the Quik- Change blade clamp (A) Fig. 2 and turn it counter-clockwise. 3. Remove the Quik-Change blade clamp, release the arbor lock button, and remove the outer blade flange. 4. Retract the telescoping guard (A) Fig.
9 The telescoping guard (A) Fig. 3 is a safety device important to your protection. Every time you use the saw, verify that the telescoping guard rotates freely and returns quickly and completely to its closed position. At least once a month, remove any accumulated debris (sawdust, pitch, etc.
10 0° POSITIVE STOP The saw is equipped with an adjustable positive stop at 0°. Check the accuracy of this stop periodically. To adjust: 1. Loosen the bevel adjustment lever (A) Fig. 8, and position the base for a 0° cut. Confirm that the bevel-stop sleeve (B) Fig.
11 INSTALLING THE OPTIONAL RIP GUIDE 1. Insert the rip guide (A) Fig. 14 through the slots (B). Slide the guide in until it extends through the both slots in the sawbase. 2. Place the compression spring on the thumb screw (C) Fig. 14 (supplied with the rip guide), and thread into the hole in the saw base.
12 CROSS-CUTTING Cutting directly across the grain of a piece of lumber is called crosscutting. Position the work so that the cut will be on the left. RIPPING Cutting wood lengthwise is referred to as ripping. This operation is performed in the same manner as crosscutting with the exception of supporting the workpiece.
13 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.
14 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter- Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.
デバイスPorter-Cable 324MAGの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Porter-Cable 324MAGをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 324MAGの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 324MAGの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 324MAGで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 324MAGを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 324MAGの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 324MAGに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 324MAGデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
