Porter-Cableメーカー3802の使用説明書/サービス説明書
ページ先へ移動 of 21
ESP AÑOL: PÁGINA 21 FRANÇAISE : P AGE 41 12" Compound Miter Saw Instruction Manual Part No. 900988 - 11-30-00 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence.
IMPORT ANT SAFETY INSTRUCTIONS SA VE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. This tool was designed for certain applications.DO NOT modify or use it for any application other than for which it was designed.
3 25. WARNING: SOME DUST CREA TED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer , birth defects or other repr oductive harm.
4 4 REPLACEMENT P AR TS When servicing, use only identical replacement parts. POLARIZED PLUGS: T o r educe the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way .
UNP ACKING 1. Car efully remove the machine fr om the carton. Retain all packing materials until you have inspected and satisfactorily operated the machine. WARNING: Do not connect the machine to the power source until you have r ead and understood this entire instruction manual.
6 6 MOVING T ABLE TO THE 0 DEGREE CUT -OFF POSITION 1. Rotate locking knob (A) Fig. 6, counter -clockwise as far as it will go to unlock. Depr ess lever (B) and rotate table (C) to the 0 degree straight cut-of f position, release lever (B) and tighten locking knob (A).
7 7 3. Use a straight edge (C) Fig. 7C, to make the extension table (B) even with saw table (D), and tighten the two screws (A) Fig. 7B. 4. Attach the fence slide support (E) Fig. 7D, to the extension table (B) by using the two 1 1/4” long hex head screws, 5/16” lockwashers and 5/16” flat washers (F).
9. Position lock handle (M) Fig. 7J, on stud and replace scr ew and spring (L) that were removed in STEP 7 . NOTE: Lock handle (M) is spring-loaded and can be repositioned by lifting up on handle. A TT ACHING DUST BAG Depress spring clips (A) Fig. 8, of dust bag (B) and clip dust bag (B) onto end of dust chute.
9 9 DANGER: A TURNING SAW BLADE CAN BE DANGEROUS. AFTER COMPLETING CUT , RELEASE SWITCH TRIGGER (A) FIG. 12, TO ACTIV A TE BLADE BRAKE. KEEP CUTTINGHEAD DOWN UNTIL BLADE HAS COME TO A COMPLETE STOP . WARNING: THE TORQUE DEVELOPED DURING BRAKING MA Y LOOSEN THE ARBOR SCREW .
10 10 T o adjust the sliding fit between the movable table and the base, turn nut (A) Fig. 14, clockwise to increase the sliding fit (opposite to decrease the fit). This adjustment should not be so tight that it restricts the r otating movement of the table, or so loose that it affects the accuracy of the saw .
11 11 A TT ACHING OPTIONAL WORK CLAMP The work clamp is an important accessory . After purchase, the work clamp can be attached to any one of the four holes (A) Fig. 18, provided on the base of the machine, (three of which ar e shown). 1. Thread lock knob (B) Fig.
12 1. The cuttinghead of your compound miter saw can be tilted to cut any bevel angle from a 90 degr ee straight cut-off to a 45 degr ee left bevel angle by loosening bevel lock handle (A) Fig. 23, tilting cuttinghead (B) to the desired angle, and tightening lock handle (A).
13 13 ADJUSTING 0 AND 45 DEGREE BEVEL POSITIVE STOPS 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. Adjust saw so that both bevel and miter pointers are set at 0 degrees. Tighten bevel lock handle and lock cuttinghead in down position. 3. Place one end of a square (A) Fig.
14 14 Correct adjustment pr ovides for a good snug sliding fit between these two parts. This adjustment should not be so tight that it restricts the tilting movement of the trunnion (A) when bevel cutting, or so loose that it af fects the accuracy of the saw cut.
15 15 TYPICAL OPERA TIONS AND HELPFUL HINTS 1. Before cutting, make certain the cutting arm and table area ar e at their correct settings and firmly locked in place. 2. Before cutting, determine that the workpiece is the right size for the saw . 3. Place the workpiece on the table and hold or clamp it firmly against the fence.
16 16 CUTTING BOWED MA TERIAL 1. When cutting flat pieces, first check to see if the material is bowed. If it is, make sure the material is positioned on the table as shown in Fig. 39. 2. If the material is positioned the wrong way , as shown in Fig. 40, the workpiece will pinch the blade near the completion of the cut.
17 17 CUTTING CROWN MOULDING One of the many features of the saw is the ease of cutting crown moulding. The following is an example of cutting both inside and outside corners on 52/38 degree wall angle crown moulding.
18 18 MAINTENANCE CHANGING THE BLADE WARNING: USE ONL Y CROSS-CUTTING SAW BLADES. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT GUARD 1. Use only 12" diameter blades with 1" arbor holes that are rated for 4200 RPM or higher .
19 19 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies, depends on the load on the motor . Check the brushes after the first 50 hours of use of a new machine, or after a new set of brushes has been installed.
20 20 NOTES.
The following are trademarks of POR TER-CABLE Corporation (Las siguientes son marcas registradas de POR TER-CABLE S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE Corpor.
デバイスPorter-Cable 3802の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Porter-Cable 3802をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 3802の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 3802の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 3802で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 3802を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 3802の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 3802に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 3802デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。