Porter-Cableメーカー38239の使用説明書/サービス説明書
ページ先へ移動 of 23
ESP AÑOL: PÁGINA 23 FRANÇAISE : P AGE 43 Double Insulated 1 0" Bench T op T able Saw Instruction Manual Part No. 912933 - 09-15-03 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence.
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT .
4 ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine.
5 FOREWORD The Porter -Cable Model 3812 is a 10" Bench T op T able Saw . The saw comes with a 26"x20" table surface with a rip fence extension wing which provides a 24½" rip capacity for ripping 4x8 sheets.
6 CAR TON CONTENTS Fig. 2 1 2 3 4 5 6 7 8 9 1. Saw 2. Fence 3. T able Insert 4. Blade Guard and Spreader Assembly 5. Blade Wrench (2) 6. Miter Gauge 7.
7 ASSEMBL Y BLADE RAISING AND LOWERING HANDWHEEL Insert the 1-3/4" screw (D) Fig. 4, thr ough handle (E). Assemble handle (E) to handwheel (A) by threading screw (D) clockwise into handwheel as shown in Fig. 5. Handle (E) should rotate fr eely on screw (D).
8 6. NOTE: The anchor block (B) Fig. 6, has been adjusted at the factory so that the spreader will be aligned with the saw blade which is supplied with the saw . When changing to blades with dif ferent widths it may be necessary to adjust the anchor block (B) Fig.
9 RIP FENCE TO SA W T ABLE 1. The rip fence may be used on the right or left hand side of the saw table. Lift locking handle (A) Fig. 12, and position the front end of the fence on the fr ont fence rail as shown.
10 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING SA W The “ON/OFF” switch (A) Fig 16, is located on the front of the saw cabinet. T o tur n the saw “ON” pull the “ON/OFF” switch (A) out. T o tur n the saw “OFF”, push in on the “ON/OFF” switch (A).
11 ADJUSTING 0 AND 45 DEGREE POSITIVE STOPS Y our saw is equipped with positive stops for rapid and accurate positioning of the saw blade at 0 and 45 degrees to the table. This saw has the capability to go 2 degrees beyond 0 and 45 degr ees (-2º to 47º).
12 RIPPING THIN STOCK T o adjust the fence, pull up on lever (B) so that the top of the rip fence can be removed, and r epositioned on the rip fence as shown in Fig. 25. This is only necessary when the fence guide rails are extended. When using the guide rails for ripping, the fence must be positioned as shown in Fig.
13 MITER GAGE OPERA TION AND ADJUSTMENTS When straight cross-cutting (blade set 90 degr ees to the table) the miter gage can be used in either table slot. When bevel cross-cutting (blade tilted) only use the miter gage in the right table slot where the blade is tilted away from the miter gage and your hands.
14 Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig.
15 If the ripped work is less than 4 inches wide, a PUSH STICK should always be used to complete the feed, as shown in Fig. 35. The PUSH STICK can easily be made from scrap material as explained in the section “CONSTRUCTING PUSH STICK.
16 The dado head set (D) Fig. 40, is assembled to the saw arbor as shown. IMPORT ANT : The blade guard and splitter assembly cannot be used when dadoing and must be removed. Auxiliary jigs, fixtur es, push sticks and feather boards should also be used.
MAINTENANCE CHANGING THE BLADE 1. DISCONNECT MACHINE FROM POWER SOURCE. USE ONL Y 10" DIAMETER SAW BLADES RA TED FOR 4600 RPM OR HIGHER WITH 5/8" ARBOR HOLES. 2. Remove the table insert (A) Fig. 44, and raise the saw blade to its maximum height.
18 SERVICE AND REP AIRS All quality tools will eventually requir e servicing or replacement of parts due to wear fr om normal use. These operations, including brush inspection and replacement, should ONL Y be performed by either an AUTHORIZED PORTER-CABLE SERVICE ST A TION or a POR TER-CABLE • DEL T A F ACTOR Y SERVICE CENTER.
19 19 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT.
20 NOTES.
21 NOTES.
22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S.
デバイスPorter-Cable 38239の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Porter-Cable 38239をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 38239の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 38239の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 38239で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 38239を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 38239の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 38239に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 38239デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。