Porter-Cableメーカー4112, 4113, 4114, 4115の使用説明書/サービス説明書
ページ先へ移動 of 15
Part No. 900487 - 09-12-03 Dovetail Fixtur e/Jig Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. _____________________________________ T ype __________________________________________ Serial No.
2 1. KEEP WORK AREA CLEAN. Cluttered ar eas and benches invite injuries. 2. A VOID DANGEROUS ENVIRONMENT . Don’t expose power tools to rain. Don’ t use power tools in damp or wet locations. Keep area well lit. A void chemical or corrosive envir onment.
3 16. A VOID UNINTENTIONAL ST ARTING. Do not carry a plugged-in tool with finger on switch. Be sur e switch is off when plugging in. Keep hands, body and clothing clear of blades, bits, cutters, etc. when plugging in the tool. 17. OUTDOOR USE EXTENSION CORDS.
NOTE: Refer to Fig. 1 for the various parts of the Model 4112 Dovetail Fixture/Jig. 1. Insert jam nuts, item 18, into each of the outside recessed ar eas on front of the base, item 8.
5 IDENTIFYING DRAWER P ARTS It is recommended that scrap lumber be used when making your first dovetail cut so all adjustments and fits can be checked to insure a satisfactory joint. Once the templet and r outer have been set up to rout a satisfactory dovetail joint, any number of joints can be made.
6 1 / 2 " HALF-BLIND DOVET AILS PREP ARING ROUTER 1. DISCONNECT ROUTER FROM POWER SOURCE. 2. Insert templet guide, (A) Fig. 4, in hole (B), in router sub-base (C). 3. Install templet guide locknut (D) on templet guide and firmly tighten to lock templet guide in sub-base.
7 2. Place drawer front “inside up” under top clamp bar and against side of drawer which is extending above surface of Dovetail Fixture/Jig. 3. Place the 1 / 2 " half-blind dovetail templet on top of the drawer fr ont. Using a standard scale or ruler , adjust locknuts, item 7, Fig.
8 9. Fig. 11 shows both the left and right corner of a drawer fitted together after they were both routed fr om the left end of the templet. Note the location of partial pins on drawer sides. 10. If for appearance reasons the partial pins ar e desired to be in the same location of both sides of the drawer as shown in Fig.
1 / 4 " HALF-BLIND DOVET AILS PREP ARING ROUTER Prepar e router the same as for 1 / 2 " half-blind dovetails except install 42054 templet guide, 43639 bit, and adjust depth of cut (B) Fig.
10 1 / 2 " AND 1 / 4 " HALF-BLIND RABBETED DOVET AILS PREP ARING ROUTER Prepar e router the same as that for 1 / 2 " or 1 / 4 " half-blind dovetails depending on size to be cut.
11 1 / 2 " BOX JOINTS NOTE: Any material up to 13 / 16 " thick can be joined together with box joints. PREP ARING ROUTER Prepar e router the same as for 1 / 2 " half-blind dovetails except install 1 / 2 " straight bit and adjust depth of cut, (B) Fig.
12 ROUTING BOX JOINTS 1. Before turning on router , place it on templet and make sure bit will not hit Dovetail Fixtur e/Jig as it cuts into scrap material. 2. Carefully r out box joints. 3. Loosen front clamp, r otate material as shown in Fig. 21 and position up against templet and edge guide.
13 MAINTENANCE ACCESSORIES KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . Clean all plastic parts with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
14 POR TER-CABLE LIMITED ONE YEAR W ARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original pur chase.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.
デバイスPorter-Cable 4112, 4113, 4114, 4115の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Porter-Cable 4112, 4113, 4114, 4115をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 4112, 4113, 4114, 4115の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 4112, 4113, 4114, 4115の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 4112, 4113, 4114, 4115で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 4112, 4113, 4114, 4115を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 4112, 4113, 4114, 4115の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 4112, 4113, 4114, 4115に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 4112, 4113, 4114, 4115デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
