Porter-Cableメーカー844の使用説明書/サービス説明書
ページ先へ移動 of 23
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage.
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm.
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6 5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use battery tools only with specifically designated battery packs.
7 ADDITIONAL SPECIFIC SAFETY RULES continued SAVE THESE INSTRUCTIONS! g) Always use blades with correct size and shape (diamond versus round) of arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.
8 SAVE THESE INSTRUCTIONS! Lower Guard Safety Instructions p) Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position.
9 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ...................
10 7 . Do not use an extension cord unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used, make sure: A. That the pins on plug of extension cord are the same number, size and shape as those of plug on charger.
11 CHARGING THE BA TTERY P ACK Before using your cordless tool for the first time, fully charge the battery pack. If the battery pack is installed, remove it by following instructions under INSTALLING OR REMOVING BATTERY PACK. NORMAL CHARGING Make sure that the power circuit voltage is the same as that shown on the charger specification plate.
12 BA TTER Y OPERA TION DIAGNOSTICS The Model 8924 Charger is equipped with a diagnostic system that automatically checks the battery pack each time a pack is inserted into the charger. If no problems are found, the charger will automatically switch to “Fast Charge” mode as described in " NORMAL CHARGING".
13 FOREWORD The Porter-Cable Cordless Circular Saw is designed to cut 2" finished lumber at 45°, using a 150mm (6") diameter, ultra thin-kerf blade having a 1/2" diameter mounting hole. NOTE: This tool is shipped completely assembled. No assembly time or tools are required.
14 3 . While holding the blade lock engaged, use the blade wrench to loosen the blade retaining bolt by rotating clockwise. NOTE: The blade bolt has a left-hand thread. 4. Remove the blade retaining bolt, release the blade lock, and remove the outer blade flange.
15 TO ADJUST DEPTH OF CUT Adjust the depth of cut so that the saw blade just protrudes through the thickness of workpiece being cut. To adjust the depth of cut: Remove the battery pack. 1. Lift up the depth adjusting lever (H) Fig. 9 at the rear of the saw.
16 90° AND 45° BEVEL POSITIVE STOPS This saw is equipped with adjustable positive stops for both 90° (N) Fig. 12, and 45° bevel cuts (O) Fig. 12. Although these have been set at the factory, check them occasionally to ensure accuracy. TO ADJUST 90° POSITIVE STOP Remove the battery pack.
17 Remove the battery pack. 1. Adjust the saw for a 90° cut. 2. Loosen the two screws (Q) Fig. 15. 3. Place a straight edge along the side of the blade, touching the set of the blade teeth at both the front and rear of blade (Fig. 16). 4. Align the left edge of the notch indicator with the straight edge and tighten the two screws (Q) Fig.
18 2. Insert the nozzle in the exhaust opening and push in until seated. 3. To remove, grasp the nozzle and pull out. Never direct sawdust toward anyone. To avoid personal injury from flying sawdust, keep the exhaust cover closed when the nozzle is not attached.
19 HOW TO USE THE SAW For your protection, effective control of this powerful saw requires two-handed operation. The saw may be operated either right-handed (Fig. 21) or left- handed (Fig. 22). Support the work properly and hold the saw firmly to prevent loss of control which could cause personal injury.
20 For narrow rip cuts, the rip guide is available as an accessory. Guide the saw by keeping the inner face of the rip guide (Fig. 20) tight against the edge of the board. For making wider cuts, - plywood and wide sheets - clamp or tack a straight-edge guide or a wooden guide strip on the workpiece.
21 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.
22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.
デバイスPorter-Cable 844の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Porter-Cable 844をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 844の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 844の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 844で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 844を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 844の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 844に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 844デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。