Porter-Cableメーカー877の使用説明書/サービス説明書
ページ先へ移動 of 17
T wo-Speed Cor dless Hammer Drill/Drivers Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e reference. Model No. ______________________________________ T ype ___________________________________________ Serial No.
2 GENERAL SAFETY RULES FOR ALL BA TTER Y OPERA TED TOOLS WARNING! READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury .
3 3. Avoid accidental starting. Be sur e switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents. 4. Remove adjusting keys or wrenches befor e turning the tool on.
4 SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wir e will also make exposed metal parts of the tool “live” and shock the operator .
5 5. Do not abuse cord. Never carry char ger by cord or yank it to disconnect from r eceptacle. Pull by plug rather than cord when disconnecting char ger . Have damaged or worn power cord and strain reliever r eplaced immediately . DO NOT A TTEMPT TO REP AIR POWER CORD.
6 ADDITIONAL SAFETY RULES FOR HAMMER-DRILLS 1. Apply forward for ce only on pistol grip handle and ONL Y with your hands when drilling. 2. Do not use bits lar ger than those recommended. They may cause personal injury due to jamming and loss of control.
7 INST ALLING AND REMOVING DRILL AND SCREWDRIVER BITS 1. CAUTION: Always set reversing button to center (locked OFF) position when installing and removing bits. 2. The three-jaw chuck is designed for self-centering of the bit. Open jaws lar ge enough by turning outer sleeve (A) Fig.
8 DRIVER BIT STORAGE Convenient storage areas with r etaining clip (B) Fig. 4, for screwdriver bits ar e provided on each side of the tool. OPERA TION CHARGING THE BA TTER Y P ACK GENERAL Before using your cor dless tool for the first time, the battery pack should be fully char ged.
9 DIAGNOSTICS The Models 8604 and 8624 char gers are equipped with a diagnostic system that automatically checks the battery pack each time a pack is inserted into the char ger . If no problems ar e found, the charger will automatically switch to “Fast Char ge” mode as described in NORMAL CHARGING.
10 HOW TO HOLD THE HAMMER DRILL/DRIVER WARNING: The front end of the Hammer Drill/Driver may be made live if the tool drills into live wiring in the wall. TO PREVENT ELECTRICAL SHOCK, THE HAMMER DRILL/DRIVER MUST BE HELD AS SHOWN IN FIG. 7. GENERAL DRILLING 1.
11 DRILLING WOOD In addition to the instructions listed under GENERAL DRlLLlNG, the following also apply: 1. When using twist drills in wood, they should be withdrawn from the hole frequently to clear chips built up in flutes to avoid overheating and burning work.
12 2. Install proper bit that fits scr ew to screwdriver . 3. Set torque adjusting collar for desir ed torque and set speed selector to LOW . 4. Set screwdriver for corr ect rotation. 5. Start screw straight in hole with fingers. 6. Place bit on screw , start screwdriver and exert pressur e to drive screw .
13 CAUTION: Extr eme care should be taken in the event bit should become jammed in the hole so that drill can be stopped immediately . See ADDITIONAL SAFETY RULES FOR HAMMER DRILL/DRIVERS, Number 7. MAINTENANCE KEEP TOOL CLEAN All plastic parts should be cleaned with a soft damp cloth.
14 5. Place the short end of a large allen wr ench ( 1 / 4 " or larger) into the chuck. Align wrench flats with chuck jaws and tighten chuck secur ely . While supporting chuck on a solid surface, position allen wrench to left (see Fig. 9) and strike wrench a sharp blow with a hammer to loosen chuck.
15 NOTES 900470 - 11-30-00.QXD 9/25/02 11:10 AM Page 15.
16 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE · DEL T A Corporation (Las siguientes son marcas registradas de PORTER-CABLE · DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la .
デバイスPorter-Cable 877の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Porter-Cable 877をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 877の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 877の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 877で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 877を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 877の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 877に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 877デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。