Porter-Cableメーカー8823の使用説明書/サービス説明書
ページ先へ移動 of 17
T wo-Speed Cor dless Driver/Drill and Charger Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e reference. Model No. ______________________________________ T ype ___________________________________________ Serial No.
2 GENERAL SAFETY RULES FOR ALL BA TTER Y OPERA TED TOOLS WARNING! READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury .
3 3. Avoid accidental starting. Be sur e switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents. 4. Remove adjusting keys or wrenches befor e turning the tool on.
4 SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wir e will also make exposed metal parts of the tool “live” and shock the operator .
5 from r eceptacle. Pull by plug rather than cord when disconnecting char ger . Have damaged or worn power cord and strain reliever r eplaced immediately . DO NOT A TTEMPT TO REP AIR POWER CORD. 6. Make sure cor d is located so that it will not be stepped on, tripped over , or otherwise subjected to damage or stress.
6 FUNCTIONAL DESCRIPTION FOREWORD Y our Porter -Cable Cordless Driver/Drill is designed to drill holes and drive fasteners in various materials as indicated in the following chart: SWITCH OPERA TION Squeeze trigger switch (A) Fig. 1, to start motor . Release trigger to stop motor .
7 3. Clean and insert smooth end of bit as far as it will go into the chuck, or up to the flutes for small bits. 4. While holding the bit with one hand, turn outer sleeve (A) Fig. 2, clockwise until the bit is gripped in the chuck. 5. Tighten chuck by holding chuck ring (B) Fig.
8 OPERA TION CHARGING THE BA TTER Y P ACK GENERAL Before using your cor dless Driver/Drill for the first time, the battery pack should be fully char ged. If the battery pack is installed in the Driver/Drill, remove it by following instructions under INST ALLING OR REMOVING BA TTER Y P ACK.
9 • Green light (A) glows continuously and red light (B) flashes: indicates that the battery pack is receiving a “Fast Char ge”, but the battery pack voltage is low . It is not unusual for a new , or a fully discharged battery pack to give this indication for the first several minutes of char ge.
10 3. Set REVERSING BUTTON for clockwise rotation. 4. CAUTION: Make sur e work is held securely in vise or clamped in place prior to starting drilling operation. Loose work may spin and cause bodily injury . 5. Locate exact center for hole to be drilled and using a center punch, make a small dent in work.
11 DRILLING MET AL In addition to the instructions listed under GENERAL DRlLLlNG, the following also apply: 1. Use only good quality sharp high speed steel twist bits when drilling metal. 2. Start drilling with slow speed and gradually increase speed as drill cuts.
12 DRIVING SELF-T APPING SCREWS 1. Drill pilot hole of correct size as r ecommended by screw manufactur er for fastener being used. 2. Install proper bit that fits scr ew to screwdriver . 3. Set torque adjusting collar for desired tor que and set speed selector to LOW .
13 CHUCK REPLACEMENT 1. CAUTION: Remove battery pack to prevent accidental start-up. 2. Open chuck jaws as wide as possible to gain access to the chuck retaining scr ew . 3. Remove chuck retaining scr ew by turning it clockwise (left-hand thread) with an allen wrench.
14 ACCESSORIES The testing of this tool has been accomplished with the following accessories. For safest operation, it is recommended that only these accessories be used with this product. WARNING: Since accessories other than those listed have not been tested with this product, use of such accessories could be hazardous.
15 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase.
NOTES 900469 - 11-30-00.QXD 9/25/02 11:26 AM Page 16.
The following are trademarks of PORTER-CABLE · DEL T A Corporation (Las siguientes son marcas registradas de PORTER-CABLE · DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la .
デバイスPorter-Cable 8823の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Porter-Cable 8823をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable 8823の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable 8823の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable 8823で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable 8823を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable 8823の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable 8823に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable 8823デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。