Porter-CableメーカーJig Sawの使用説明書/サービス説明書
ページ先へ移動 of 16
T enoning Jig (Model 34-183) INSTRUCTION MANUAL P ART NO. 1342471 - 02-02-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES 1. DISCONNECT THE POWER SOURCE to the machine before attaching or adjusting the jig. 2. MAKE SURE THA T THE BLADE HAS COME TO A COMPLETE STOP befor e adjusting the jig or the workpiece.
5 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose).
6 6. Use the supplied 3mm hex wrench to loosen the set scr ew (M) Fig. 6. Remove the micro-adjustment assembly (N) fr om the tenoning jig (Fig. 7). M N H R P H R G Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 ADJUSTING THE GUIDE BAR TO THE T ABLE SLOT Disconnect Machine from Power Sour ce C A B Fig.
7 2. Place the tenoning jig guide bar (A) Fig. 12 into the left miter slot (D) and slide the tenoning jig back and forth to determine if it has side-to-side play . If the tenoning jig slides easily through the miter slot without side-to-side play , no adjustment is necessary .
8 Fig. 18 OPERA TION ADJUSTMENTS 1. For rapid adjustment of the work support plate (A) Fig. 19, toward or away from the saw blade, loosen levers (B) and (C) and move jig (D). Tighten levers (B) and (C). 2. Y ou can fine-adjust the work support plate (A) Fig.
9 J G P R S TENONING JIG USE This jig is intended to perform cheek cuts only . Cheek cuts are made prior to the shoulder cuts, which ar e made on a table saw using the miter gauge.
10 • The objective is to make the parts fit closely together . Maximize the gluing surface by making the tenon as long as possible (approximately 1/2 the width of the stile or longer , if using narrow stock). Balance the joint by using the same amount of wood in the tenon as in the combined thickness of the mortise walls (Fig.
11 8. Load and secure the workpiece (L) Fig. 31 on the tenoning jig and adjust the jig to perform the third and fourth cosmetic cheek cuts. Connect the machine to the power source, turn the saw “on”, and make the cuts. NOTE: When cutting the cosmetic cheek cuts, do not use the spacer block (K) Fig.
12 EXAMPLES OF MORTISE-AND-TENON JOINTS Position the wooden stop block (S) Fig. 34 in front of the saw blade to prevent the workpiece fr om being trapped between the saw fence and the saw , causing kickback. Make sure that the workpiece is clear of the wooden stop block (S) before contacting the saw blade.
13 HAUNCHED TENON CONCEALED HAUNCHED TENON MITERED TENON TENON ENDS MITERED SAW CUTS THROUGH-WEDGED TENON BARE F ACED TENON SIMPLE MORTISE AND TENON MORTISE CHEEK OF TENON SHOULDER OF TENON BLIND-WEDG.
14 TROUBLESHOOTING GUIDE For assistance with your tool, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
15 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
デバイスPorter-Cable Jig Sawの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Porter-Cable Jig Sawをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPorter-Cable Jig Sawの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Porter-Cable Jig Sawの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Porter-Cable Jig Sawで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Porter-Cable Jig Sawを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPorter-Cable Jig Sawの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Porter-Cable Jig Sawに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPorter-Cable Jig Sawデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
