POSIFLEX Business MachinesメーカーHT-2212の使用説明書/サービス説明書
ページ先へ移動 of 20
Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications.
Part 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences.
Part 3 BRIEF INTRODUCTION TH E USER’S MANUAL The purpose of this manual is to guide the user in the initial installation and general use of the Posiflex POS terminals HT - 2212 Pro series. It does not explain any application software that may be supplied with it.
Part 4 THE ST ANDARD FEATURES CPU: VIA C7 1 GHz ; HDD: 4 0 GB or above; RAM: 256 MB DDR2 upgradeable to 2 GB max. Ethernet Networking: The standard network port works with both 10 Base T and 100 Base T. Serial Ports: There are 4 serial ports in a HT - 2212 Pro system.
Part 5 type Finger Print Sensor f) Customer display : Pole mount 2 x 20 VFD display PD - 2601 o r LCD pole display PD - 7321 or 2 nd LCD Screen : LM - 2010 g) Audio amplifier and internal speakers h) Wireless LAN Adaptor: inside back cable cover, IEEE 80 2.
Part 6 INSTALLATION GUIDES IMPORTANT Please do not connect the power cord or turn on the main unit until yo u have fully read the installation guides and followed the instructions!!! TECHNICAL ENHANCE.
Part 7 of the system unit before pressing these 2 springs. The LCD and touch panel may flip forward by gravity and get or cause damage by hitting anything in front of the system unit. POWER ADAPTOR The powe r connector resides in the lower left corner of main connector area.
Part 8 LCD CASHI ER DISPLAY Push down the round plastic button at rear of the display base as circled in right picture to adjust the display up and down.
Part 9 PROGRAMMABLE KEYBOARD & KEYPAD (OPTION) All types of Posiflex programmable keyboards can be applied in HT system. Most recommended keyboard models are: KB - 6000, KB - 6200 series and KB - 6600. Just connect it to the PS /2 KB port in the main connection area.
Part 10 control of the COM1 serial port . Use the cable supplied with the Posiflex cash drawer (Part No. 21863018010 ) for connection to the CR port in HT system.
Part 11 OPERATING SYSTEM INSTALLATION This product is h ighly professionalized equipment. The installation of an OS into a machine without any preloaded OS could constitute major difficulty for averag.
Part 12 USING THE HT SYSTEM BEFORE POWER ON – A Check List It is very important that you check the following operational points: Ventilation This terminal must NOT be operated in an environment with restricted ventilation.
Part 13 replace the used up UPS battery at power off as soon as possible . Emergency treatment: The battery is constructed maintenance free and leakproof. Its storage space in HT system also provides very good protection as long as the ambient temperature remains below 30 ° C and the ventilation of the HT system remains free.
Part 14 usage of the battery power, the flashing LED will kee p on flashing for few seconds before steady till the AC supply is stable. POWER ON/OFF CONTROL The HT terminal implements electronic power control, such that the main power to the system may be controlled by many methods as below: 1.
Part 15 Emergency Power Off In case of serious system halt due to any reason, the system could fail to be powered off through normal means. Press and hold the Power ON/OFF Switch for Emergency Power Off. Release the switch after the system powered off.
Part 16 drag and drop feature. If the point is touched, released and touched within a shor t time interval, it will simulate double - clicking left button of the mouse. Emulating the click on right button of a real mouse is further illustrated in paragraph below.
Part 17 For bar code card reading, it is still required to insert the card t o the bottom with bar code stripe facing the mark aside the slot. F or smart card reading, please insert the end of the smart chip first and have the chip facing the mark aside the side slot of KP - 200 as in the right picture .
Part 18 VENTILATION MAINTENANCE To keep this equipment in orderly service, following maintenance should be performed on a regular basis. Removing F ront Cover Please first remove any power and signal connection to this equipment.
Part 19 Cleaning for Front Ventilation Use vacuum cleaner to remove any dust or threads accumulation away from both the ventilation holes on front cover and ventilation grids on chassis exposed after removal of the front cover. Replacing Front Cover Foll ow the opposite procedure as removing the front cover to replace the front cover in position.
Part 20 Cleaning for Side Ventilation Use vacuum cleaner to remove any dust or threads accumulat ion away from outsides of both ventilation grids on chassis exposed after removal of the front cover as in pictures below and close back the top cover when done.
デバイスPOSIFLEX Business Machines HT-2212の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
POSIFLEX Business Machines HT-2212をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPOSIFLEX Business Machines HT-2212の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。POSIFLEX Business Machines HT-2212の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。POSIFLEX Business Machines HT-2212で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
POSIFLEX Business Machines HT-2212を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPOSIFLEX Business Machines HT-2212の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、POSIFLEX Business Machines HT-2212に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPOSIFLEX Business Machines HT-2212デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。