Poulanメーカー199329の使用説明書/サービス説明書
ページ先へ移動 of 20
OWNER'S MANUAL MODEL NUMBER: PP930ES SNOW THROWER Alwa ys W ear Ey e Pr otection During Operation IMPORT ANT MANUAL Do Not Throw A way W ARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. Fail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 PRODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quarts and T ype: Unleaded Regular only Oil T ype SAE 30 (above 40°F) (API SG–SL): SAE 5W-30 or 10W-30 (0° to +40°F) SAE 0W-30 (below 0°F) Oil Capacity: 26 Ounces Spark Plug: Champion RN4C (Gap: .030") CONGRA TULA TIONS on your purchase of a new snow thrower .
4 P ARTS P ACKED SEP ARA TEL Y IN CART ON.
5 Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 ASSEMBL Y / PRE-OPERA TION INST ALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod to lower handle. 2. Insert rod into speed control bracket and secure with retainer spring. INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown.
7 ASSEMBL Y / PRE-OPERA TION 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 2. With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket.
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 OPERA TION Throttle/engine control - used to se lect either F AST or SLOW engine speed and to STOP the engine. T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow).
10 TO CONTROL SNOW DISCHARGE (See Fig. 14) W ARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.
11 OPERA TION TO THROW SNOW (See Fig. 15) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow.
12 TO ADJUST SKID PLA TES (See Fig. 19) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface.
13 OPERA TION COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key into the ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in F AST position. 3. Rotate choke control to FULL position.
14 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE AUGER GEAR CASE • The gear case was fi lled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease.
16 CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower . 4. Connect spark plug wire to spark plug. W ARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure throttle is in STOP position.
17 BEL T KEEPER IDLER ARM SQUARE HOLE BOL T LOCK W ASHER TRACTION DRIVE BEL T CLUTCHING IDLER ARM BRACKET AUGER BEL T FLA T WASHER AUGER PULLEY AUGER HOUSING FRAME ENGINE PULLEY LOCKW ASHER BOL T FIG.
18 SER VICE AND ADJUSTMENTS ST ORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.
19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position.
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship.
デバイスPoulan 199329の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Poulan 199329をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan 199329の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan 199329の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan 199329で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan 199329を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan 199329の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan 199329に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan 199329デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。