Poulanメーカー415242の使用説明書/サービス説明書
ページ先へ移動 of 32
OWNER'S MANUAL MODEL NUMBER: PR524 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 6. When cleaning, repairing or inspecting the snow thrower , stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the en- gine.
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON.
5 Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 AS SEMBL Y / PRE-OPERA TION INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.
7 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 OPERA TION Throttle/engine control - used to se lect either F AST or SL OW engine speed and to STOP the engine. T raction drive control lever - used to engage power -pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow).
10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles.
11 OPERA TION TO MOVE FORWARD AND BACK WARD (See Fig. 16) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system.
12 ENGINE OIL FILL CAP / DIPSTICK FUEL SHUT - OFF VAL VE PRIM ER SAFETY IG NI TION KEY THROT TLE CHOKE CONTROL RECOIL ST ARTER HANDLE GAS O LINE FILLER CAP NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL L OCA TION. ACTUAL L OCA TION MA Y VARY WITH ENGINE ON Y OUR UNIT .
13 OPERA TION TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with a recoil starter . COLD ST ART 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks.
14 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease.
16 3. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely . CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower .
17 SERVICE AND ADJUSTMENTS 1. REMOVE GASOLINE FROM FUEL T ANK - Drain gasoline from fuel tank into a suitable container , out- doors, away from fire or flame.
18 SERVICE AND ADJUSTMENTS STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.
19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition switch OUT . 2. Push safety ignition switch IN. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4.
20 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) AUGER HOUSING / IMPELLER ASSEMBL Y .
21 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) AUGER HOUSING / IMPELLER ASSEMBL Y KEY P ART NO . NO. DESCRIPTION 4 191079 Pulley , Impeller 5 188909 Bearing Assembly , Flange 6 155377 Nut,.
22 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) CONTROL P ANEL / DISCHARGE CHUTE 1 2 6 7 4 5 6 8 8 19 2 2 26 28 27 27 25 20 29 3 18 17 10 15 12 21 9 16 14 13 31 34 30 33.
23 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) CONTROL P ANEL / DISCHARGE CHUTE KEY P ART NO . NO. DESCRIPTION 1 414280 Knob, Lever 2 17501010 Screw #10-24 x 5/8 3 179096X479 Strap, Slotte.
24 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) HANDLES 34 42 37 10 11 15 23 22 27 27 22 11 15 12 12 13 15 49 49 48 47 16 17 16 17 15 14 32 31 32 30 31 7 6 36 2 5 5 5 1 8 28 28 9 18 19 26 2.
25 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) HANDLES KEY P ART NO . NO. DESCRIPTION 1 412682X479 Lever , Auger Control, RH 2 412681X479 Lever , T raction Drive Control, LH 5 169675 Retai.
26 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) DRIVE 4 4 4 4 4 2 2 43 11 1 1 22 5 5 5 2 2 20 41 21 17 13 3 6 14 19 18 18 15 24 36 35 34 37 31 9 12 23 26 29 25 4 4 33 28 32 27 44.
27 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) DRIVE KEY P ART NO . NO. DESCRIPTION 1 401619 Chain, Drive 2 751153 Nut, Lock 5/16-18 3 402882 Clip, Retainer 4 17490508 Bolt, Hex Head 5/16-.
28 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) CHAS SIS / ENGINE / PULLEYS 6 19 17 10 21 22 23 2 3 4 6 42 8 9 12 13 15 27 26 25 24 18 7 20 14 5 40 46 44 49 50 51 52 35 34 33 38 37 39 43 11.
29 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) CHAS SIS / ENGINE / PULLEYS KEY P ART NO . NO. DESCRIPTION 1 414557 Spring, T raction Idler 2 180522 Pulley , Idler (2-1/4) 3 - - - Engine, T.
30 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) WHEELS / DECALS 3 2 7 7 5 5 6 6 4 7 1 2 5 3 1 4 2 1 7 6 8 9.
31 REP AIR P ARTS SNOW THROWER - MODEL PR524 (96192001501) WHEELS / DECALS KEY P ART NO . NO. DESCRIPTION 1 187831X421 Wheel Assembly , 13", LH 2 155443 Pin, Klik 1/4 3 187866X421 Wheel Assembly , 13", RH 4 146315 Screw , Hex Head 5/16-18 x 3/4 5 179830 Bearing, Axle 6 174697 Washer , Thrust (1") 7 17490508 Bolt KEY P ART NO .
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship.
デバイスPoulan 415242の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Poulan 415242をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan 415242の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan 415242の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan 415242で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan 415242を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan 415242の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan 415242に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan 415242デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。