Poulanメーカー421474の使用説明書/サービス説明書
ページ先へ移動 of 40
OWNER'S MANUAL MODEL NUMBER: 96192001903 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u - fac tured to give best possible dependability and per for - mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center .
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON ®.
5 Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 AS SEMBL Y / PRE-OPERA TION INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.
7 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 OPERA TION Throttle/engine control - used to se lect either F AST or SL OW engine speed and to STOP the engine. T raction drive control lever - used to engage power -pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow).
10 TO CONTROL SNOW DISCHARGE (See Fig. 14) WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.
11 • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or reverse movement of the snow thrower . SPEED and DIRECTION are controlled by the drive speed control lever .
12 BEFORE ST ARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 21) The engine on your snow thrower has been shipped, from the factory , already filled with oil.
13 TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .
14 SAE 5W -30 Motor Oil See “ENGINE” in Maintenance section General Purpose Grease GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease.
16 3. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely . CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower .
17 SERVICE AND ADJUSTMENTS be replaced. It is recommended that the belt(s) be replaced by a qualified service center . NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.
18 SERVICE AND ADJUSTMENTS STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.
19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position.
20 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
21 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
22 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
23 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
24 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
25 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
26 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
27 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
28 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
29 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
30 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
31 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
32 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
33 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
34 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
35 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
36 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) WHEELS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
37 KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) WHEELS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
38 REP AIR P ARTS SNOW THROWER - MODEL PP11530ES (96192001903) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
39 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship.
デバイスPoulan 421474の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Poulan 421474をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan 421474の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan 421474の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan 421474で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan 421474を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan 421474の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan 421474に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan 421474デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。