Poulanメーカー96192004501の使用説明書/サービス説明書
ページ先へ移動 of 40
OWNER'S MANUAL MODEL NUMBER: XT627ES SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u fac - tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center .
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (1) POWER CORD (198563) (1) DISCHARGE CHUTE (3) RET AINER SPRINGS (169675) (2) SHEAR BOL TS 1/4-20 x 1-3/4 (192090) (2) L OCKNUTS 1/4-20 (73800400) EXTRA SHEAR.
5 AS SEMBL Y / PRE-OPERA TION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely .
6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING Y OUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
8 OPERA TION ON / OFF switch - used to STOP the engine. T raction drive control lever - used to engage power- pro pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - used to change the di rec- tion the snow is thrown.
9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles.
10 OPERA TION USING THE CLEAN-OUT TOOL (See Fig. 14) In certain snow conditions, the discharge chute may be- come clogged with ice and snow . Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or in spect ing, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped.
11 OPERA TION TO ADJUST SKID PL A TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface.
12 OPERA TION TO ST ART ENGINE Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C.
13 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
14 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease.
15 WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure the on/off switch is in the OFF position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact with plug.
16 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.
17 SERVICE AND ADJUSTMENTS ENGINE See engine manual. CARBURETOR Y our carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center .
18 STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
19 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.
20 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
21 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
22 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
23 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
24 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
25 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
26 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
27 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
28 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
29 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
30 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
31 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
32 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
33 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
34 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) CHAS SIS / ENGINE / PULLEYS 01.21.013-B 1 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
35 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) WHEELS KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
36 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
37 REP AIR P AR TS SNOW THROWER - MODEL XT627ES (96192004501) DECALS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
38 SERVICE NOTES.
39 SERVICE NOTES.
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi- als and work man ship.
デバイスPoulan 96192004501の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Poulan 96192004501をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan 96192004501の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan 96192004501の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan 96192004501で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan 96192004501を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan 96192004501の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan 96192004501に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan 96192004501デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。