PoulanメーカーHDF825Xの使用説明書/サービス説明書
ページ先へ移動 of 18
OPERA TOR'S MANU AL MODEL: HDF825X FRONT TINE TILLER AL WA YS WEAR EYE PROTECTION DURING OPERA TION Visit our website: www .poulan-pro.com WARNING: Read this Man u al and follow all Warnings and Safety Instructions. F ail ure to do so can re sult in serious in ju ry .
2 • Keep children and pets away . • Do not overload the machine capacity by attempting to till too deep at too fast a rate. • Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing. • Never allow bystanders near the unit.
3 PRODUCT SPECIFICA TIONS Gasoline Capacity: 3 Quarts (2.8L) Unleaded Regular Oil (API-SG-SL): SAE 30 (Above 32°F/0°C) (Capacity: 20 oz./0.6L) SAE 5w-30(Below 32°F/0°C) Spark Plug: Champion RC12YC (Gap: .030"/0.76mm) CONGRA TUL A TIONS on your purchase of a new tiller .
4 AS SEMBL Y OPERA TOR’S POSITION (See Fig. 1) When right or left hand is mentioned in this manual, it means when you are in the operating position (standing behind tiller handles). Y our new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
5 UNP ACK CARTON & INST ALL HANDLE (See Fig. 2) CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material. IMPORT ANT : WHEN UNP ACKING AND AS SEM BLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLE(S). • Cut cable ties securing handles.
6 KNOW YOUR TILLER READ THIS MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. REVERSE TINE CONTROL These symbols may appear on your Tiller or in literature supplied with the product.
7 hand l es_9 4 FORWARD TINE CON TROL IN “OFF ” (UP) POSITION REVERSE CONTROL e n g i n e_ a r t _ 7 1 CHOKE CONTROL THROTTLE CONTROL FORWARD TINE CON TROL IN “ON” (DOWN) POSITION TINE OPERA TION (See Fig. 5) FORWARD • Squeeze forward tine control to handle.
8 TO TRANSPORT CAUTION: Before lifting or trans port ing, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank. AROUND THE Y ARD • Tip depth stake forward until it is held by the stake spring. • Push tiller handles down, raising tines off the ground.
9 engin e_ar t _ 71 BREAKING IN YOUR TILLER Break-in your belt(s), pulleys and tine control before you actually begin tilling. • Start engine, tip tines off ground by pressing handles down and engage tine control to start tine rotation. Allow tines to rotate for five minutes.
10 MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE C he ck E ngine O i l L eve l C hange E ngine O i l O i l P ivo t P oin t s I nspe ct A ir Sc reen I nspe ct S par k A rres t er /.
11 FIG. 11 e ngine_ar t _ 12 FIG. 12 OIL DRAIN PLUG OIL FILLER PLUG OIL LEVEL TEMPERATURE RANGE ANTICIPATED BEFORE NE X T OIL CHANGE SAE VISCOSITY GRADES -20 0 30 40 8 0 100 -30 -20 0 20 30 40 F C 32 -10 10 60 5W-30 SAE 30 oi l _vis c _ c har t1 _e MAINTENANCE AIR CLEANER SCREW COV ER AIR CLEAN ER CAR TRIDGE FIG.
12 TILLER TO ADJUST HANDLE HEIGHT (See Fig. 15) F actory assembly has provided lowest handle height. Se lect handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets.
13 FIG. 18 NARROW TILLING/CUL TIVA TING - 12-3/4" P A TH (See Fig. 18) • Remove outer tines. t ine_ 6 INNER TINES ONL Y NOTE: When reassembling outer tines, be sure right tine assembly (marked “R”) and left tine assembly (marked “L ”) are mounted to correct side of tine shaft.
14 SERVICE AND ADJUSTMENTS b e lt s_ 10 FIG. 22 FORWARD MOTION (INSIDE) V -BEL T ENGINE PULLEY REVERSE IDLER ARM REVERSE IDLER PULLEY IDLER ARM PIN FIG.
15 STORAGE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remove spark plug. • Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder . • Pull starter handle slowly several times to distribute oil.
16 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in the Operation section. 3. Engine flooded. 3. W ait several minutes before attempting to start. 4. Dirty air cleaner . 4. Clean or replace air cleaner cartridge.
17 LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de- fects in materials and work man ship.
This product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit.
デバイスPoulan HDF825Xの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Poulan HDF825Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan HDF825Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan HDF825Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan HDF825Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan HDF825Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan HDF825Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan HDF825Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan HDF825Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。