PoulanメーカーPD25PH48STDの使用説明書/サービス説明書
ページ先へ移動 of 31
02153 O WNER'S MANU AL MODEL: PD25PH48STD LA WN TRA CT OR Alwa ys W ear Eye Pr otection During Operation W ARNING: Read this Owner's Manual and fol low all W arnings and Safety In struc tions. Failure to do so can result in serious injury . IMPOR T ANT MANU AL Do Not Thr ow A wa y 191950 3.
2 I. GENERAL OPERA TION • Read, understand, and follow all instr uctions in the manual and on the machine bef ore star ting. • Only allow responsib le adults, who are familiar with the in struc tions, to operate the machine . • Clear the area of objects such as rocks , to ys, wire , etc.
3 W ARNING: In order to pre vent ac ci - den tal starting when setting up, trans- port ing, ad just ing or making repairs, al ways dis con nect spark plug wire and place wire where it can not contact spark plug. W ARNING: Do not coast down a hill in neutral, you may lose contr ol of the tractor .
4 Gasoline Capacity 4.0 Gallons and type: Unleaded Regular Oil T ype (API-SF-SJ): SAE 30 (abov e 32°F) SAE 5W -30 (below 32°F) Oil Capacity: W/ Filter : 4.0 Pints W/O Filter : 3.75 Pints Spark Plug: Champion QC12YC (Gap: .040") Ground Speed (MPH): F orward: 0 – 5.
5 UNASSEMBLED P ARTS Mower Gauge Wheels (4) Washers 3/8 x 3/4 x 14 Ga. (4) Wheels (4) Adjusting Bars (4) Retainer Springs (double loop) (4) Clevis Pins (4) Locknuts 3/8-16 (4) Shoulder Bolts Nose Roll.
6 HO W T O SET UP Y OUR TRA CT OR CHECK B A TTER Y (See Fig. 2) • Lift hood to raised position. • If this batter y is put into service after month and year indicated on label (label located between terminals) charge batter y f or minimum of one hour at 6-10 amps.
7 ASSEMBL Y FIG. 3 2466 02464 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T INST ALL SEA T (See Fig. 3) Adjust seat bef ore tightening adjustment knob . • Remov e adjustment knob and fl at washer securing seat to cardboard packing and set aside f or assembly of seat to tractor .
8 02510 INST ALL MO WER AND DRIVE BEL T (See Figs. 6 and 7) Be sure tractor is on le vel surf ace and mow er suspension arms are raised with attachment lift control. Engage par k- ing brak e. • Cut and remove ties securing anti-sw a y bar and belts.
9 CHECK TIRE PRESSURE The tires on your tr actor were ov er infl ated at the factory f or shipping pur poses . Correct tire pressure is impor tant f or best cutting perf or mance . • Reduce tire pressure to PSI shown in “PRODUCT SPEC I FI CA TIONS” section of this man ual.
10 These symbols ma y appear on your tr actor or in literature supplied with the product. Lear n and understand their mean- ing. OPERA TION DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Model.
11 ELAPSED TIME AMPS 60 0 60 HOURS 1/10 000000000 0 02527 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to f amiliar iz e yourself with the locations of v ar ious controls and ad just ments.
12 OPERA TION CA UTION: Alwa ys stop tractor com- plete ly , as described above, before lea v- ing the operator's position; to empty grass catcher , etc. The operation of any tractor can result in f oreign objects thrown into the ey es, which can result in severe e ye dam age .
13 OPERA TION T O OPERA TE MO WER (See Fig. 10) Y our tractor is equipped with an operator presence sensing s witch. Any attempt b y the operator to lea v e the seat with the engine running and the attachment clutch engaged will shut off the engine.
14 OPERA TION T O ST ART ENGINE (See Fig. 7) When star ting the engine f or the fi rst time or if the engine has run out of fuel, it will take e xtra cranking time to mo ve fuel from the tank to the engine. • Be sure free wheel control is in the transmission en gaged position.
15 OPERA TION FIG. 12 00272 PURGE TRANSMISSION CA UTION: Never engage or disengage freewheel le ver while the engine is run- ning. T o ensure proper operation and perf or mance, it is rec om - mend ed that the transmission be purged bef ore operating tractor f or the fi rst time.
16 BEFORE EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace .
17 MAINTENANCE TRA CT OR Alwa ys obser v e saf ety rules when performing any main- te nance. BRAKE OPERA TION If tractor requires more than six (6) f eet stopping distance at high speed in highest gear , then brake m ust be adjusted. (See “T O ADJUST BRAKE” in the Service and Ad just ments section of this manual).
18 MAINTENANCE CLEAN AIR SCREEN Air screen must be k ept free of dir t and chaff to pre vent engine dam age from ov erheating. Clean with a wire brush or compressed air to re mov e dir t and stubborn dried gum fi bers. TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling.
19 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e very 100 hours of operation, whiche v er occurs fi rst.
20 02565 SER VICE AND ADJUSTMENTS FIG. 18 T O REMO VE MO WER (See Fig. 18) • Place attachment clutch in “DIS EN GA GED” position. • If equipped, turn height adjustment knob to low est set ting. • Lower mo wer to its lowest position. • Disengage belt tension rod from lock br ack et.
21 SER VICE AND ADJUSTMENTS MANDREL FIG. 21 FIG. 22 FIG. 20 LIFT LINK ADJUSTMENT NUT 01553 SUSPENSION ARM 02517 BO TH FRONT LINKS MUST BE EQU AL IN LENGTH TRUN NION FRONT PLA TE AS SEM BL Y NUT “C” NUT “D” 02516 FRONT -TO-BA CK ADJUSTMENT (See Figs.
22 02515 02513 SER VICE AND ADJUSTMENTS L.H. MANDREL CENTER MANDREL IDLER PULLEY R.H. MAN DREL CO VER SPRING FIG. 24 SEC OND AR Y IDLER ARM SEC OND AR Y SPRING ARM T O REPLA CE MO WER DRIVE BEL T MO WER DRIVE BEL T REMO V AL (See Fig. 23) • P ark tractor on a le v el surface.
23 02537 TRANSMISSION REMO V AL/RE PLA CE MENT Should your tr ansmission require remov al for service or replacement, it should be purged after reinstallation and bef ore operating the tractor . See “PURGE TRANS MIS SION” in the Operation section of this manual.
24 SER VICE AND ADJUSTMENTS FIG. 29 0217 9 HEX BOL T KEPS NUT POSITIVE (RED) CABLE NEGA TIVE (BLA CK) CABLE TERMINAL GU ARD TERMINAL A CCESS DOOR REPLA CING B A TTER Y (See Fig. 29) CA UTION: Do not short batter y ter mi - nals by allo wing a wrench or an y other object to contact both terminals at the same time.
25 SER VICE AND ADJUSTMENTS FIG. 30 T O REMO VE HOOD AND GRILL ASSEMBL Y (See Fig. 30) • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Grasp hood at sides, tilt to ward engine and lift off of tractor . • T o replace, re verse abo ve procedures .
26 ST ORA GE Immediately prepare your tr actor f or storage at the end of the season or if the tractor will not be used f or 30 days or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
27 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” proper ly . 2. Se e “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se veral minutes bef ore attempting to star t. 4. Bad spark plug.
28 TR OUBLESHOO TING POINTS Engine continues to run 1. Faulty oper ator-safety presence control system. 1. Chec k wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutc h department.
46 LIMITED W ARRANTY The Manuf acturer warrants to the original consumer purchaser that this product as manufactured is free from def ects in materi- als and work man ship.
47 15 DEGREES MAX. F O L D A L O N G D O T T E D L IN E T H IS IS A 15 D E G R E E S L O P E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Y our POULAN PRO product has been e xpertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical pr oducts, some adjustments or par t replacement may be necessary during the life of y our unit. FOR SER VICE OR REPLA CEMENT P ARTS: 1.
デバイスPoulan PD25PH48STDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan PD25PH48STDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan PD25PH48STDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan PD25PH48STDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan PD25PH48STDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan PD25PH48STDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan PD25PH48STDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan PD25PH48STDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan PD25PH48STDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
