PoulanメーカーPPCRT55の使用説明書/サービス説明書
ページ先へ移動 of 28
O WNER'S MANU AL MODEL: PPCR T55 REAR TINE TILLER AL W A YS WEAR EYE PRO TECTION DURING OPERA TION Visit our website: www .poulan-pr o.com W ARNING: Read this Man u al and f ollow all W ar nings and Saf ety Instr uctions . F ail ure to do so can re sult in serious in ju ry .
2 • Ne ver operate the tiller without proper guards , plates, or other saf ety protective de vices in place. • K eep children and pets awa y . • Do not ov er load the machine capacity b y attempting to till too deep at too f ast a rate. • Ne ver operate the machine at high speeds on slippery surf aces.
3 CONGRA TULA TIONS on your purchase of a new tiller . It has been designed, en gi neered and manu fac tured to giv e you the best pos sible de penda bil ity and per fo r m ance. Should you e xperience any prob lems you can not easily remedy , please contact your nearest authorized ser vice center .
4 T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Standard wrench sizes are listed. (1) Utility knif e (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA T OR’S POSITION (See Fig.
5 ASSEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. FIG. 4 UNP A CKING CART ON (See Fig. 2) CA UTION: Be careful of exposed sta ples when handling or disposing of cartoning material.
6 ASSEMBL Y INSERT CABLE CLIP (See Fig. 6) • Insert plastic cable clip into hole on the back of handle column. Push cab les into clip. A TT A CH THIS END T O SHIFT LEVER IN DI CA TO R SHIFT ROD FIG. 6 SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA TOR FIG.
7 KNO W Y OUR TILLER READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with y our tiller to familiarize y ourself with the location of various controls and adjustments. Sa ve this manual f or future reference .
8 TURNING • Release the drive control bar . • Mov e throttle control to “SLO W” position. • Place shift lev er indicator in “F” (f orward) position.
9 OPERA TION OIL LEVEL FIG. 12 BEFORE ST ART ING ENGINE IMPORT ANT : BE VERY CAREFUL NO T T O ALLOW DIR T T O ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND ST ORE IN APPRO VED , CLEAN, CO VERED CONT AINERS. USE CLEAN FILL FUNNELS.
10 R U N C H O K E OPERA TION • Soil conditions are impor tant for proper tilling. Tines will not readily penetrate dry , hard soil which may con trib ute to e xcessive bounce and diffi cult handling of your tiller . Hard soil should be mois tened before tilling; how ev er , e xtremely wet soil will “ball-up” or clump during tilling.
11 MAINTENANCE GENERAL RECOMMEND A TIONS The warranty on this tiller does not co ver items that ha ve been subjected to operator ab use or negligence. T o receiv e full value from the w arranty , the operator must main tain tiller as instructed in this manual.
12 MAINTENANCE OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG FIG. 16 Disconnect spark plug wire before perf orming any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine . Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel.
13 MAINTENANCE e ngine_ar t _ 61 FIG. 19 AIR SCREEN BLO W ER HOUS ING MUFFLER Do not operate tiller without muffl er . Do not tamper with e xhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect pe ri odi cally and re place if nec es sar y .
14 SER VICE AND ADJUSTMENTS CA UTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER T O ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited f or your tilling conditions. Handle height will be diff erent when tiller digs into soil.
15 SER VICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE EXTENSION SPRING ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY LESS TEN SION 5/8" MORE TEN SION FIG. 23 T O REPLA CE GROUND DRIVE BEL T (See Figs. 22 and 23) • Remove belt guard as described in “T O REMO VE BEL T GU ARD”.
16 SER VICE AND ADJUSTMENTS tine_13 FIG. 26 TINE REPLA CEMENT (See Figs. 24, 25, and 26) CA UTION: Tines are sharp. Wear gloves or other pr otection when han- dling tines.
17 SER VICE AND ADJUSTMENTS FIG. 27 engine_art_78 THRO TTLE CONTROL CLAMP SCREW CASING AND WIRE ENGINE T O ADJUST THRO TTLE CONTROL CABLE (See Fig. 27) The throttle control has been preset at the f actor y and ad just ment should not be necessar y .
18 ST ORA GE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remov e spark plug. • P our 1 ounce (29 ml) of oil through spark plug hole into cylinder .
19 Will not start 1. Out of fuel. 1. Fill fuel tank . 2. Engine not “CHOKED” proper ly . 2. See “T O ST AR T ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se ver al minutes before attempting to start. 4. Dir ty air cleaner . 4. Clean or replace air cleaner car tridge.
20 REP AIR P AR TS TILLER - - MODEL NUMBER PPCR T55 (96091001200), PRODUCT NUMBER 960 91 00-12 HANDLE ASSEMBL Y KEY P ART NO . NO. DESCRIPTION 17 532 10 92-29 Loc k, Handle 18 873 68 06-00 Nut, Cro wnlock 3/8-16 unc 19 819 13 16-11 W asher 13/32 x 1 x 11 Ga.
21 KEY P ART NO . NO. DESCRIPTION 2 810 04 06-00 W asher , Loc k 3/8 3 873 22 06-00 Nut, He x 3/8-16 4 532 17 01-27 Shield, Inner Belt Guard R T 5 532 16 43-29 Pin Spirol Flared 6 532 11 01-11 Le ver , Shift 7 872 11 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr .
22 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION REP AIR P AR TS TILLER - - MODEL NUMBER PPCR T55 (96091001200), PRODUCT NUMBER 960 91 00-12 MAINFRAME, RIGHT SIDE 2 873 97 05-00 Loc knut, He x, Flange 5/16-18 5 532 10 23-32 Br acket, Reinf orcement 7 532 10 21-73 Counter W eight, R.
23 12 13 15 16 14 9 9 8 5 18 23 22 21 19 18 3 2 29 31 7 6 5 4 11 10 30 28 18 32 33 34 18 48 60 24 44 18 42 43 41 49 40 39 37 38 37 50 36 20 25 27 35 25 24 44 51 58 53 52 53 transmission_19.5b KEY P ART NO . NO. DESCRIPTION NO TE: All component dimensions given in U .
24 1 2 29 29 15 1 11 11 12 12 13 14 14 24 23 26 27 22 21 20 19 11 12 16 25 33 32 16 3 4 7 8 9 5 5 23 23 28 24 18 6 5 5 30 tine_shield_16_in 12 12 11 11 10 21 532 10 21-56 Stak e, Depth 22 874 93 06-32 Bolt, He x 3/8-16 x 2 23 532 00 44-40 Hinge 24 872 14 04-04 Bolt, Carriage 1/4-20 x 1/2 Gr .
25 2 11 11 10 9 9 4 4 5 34 3 3 1 2 1 1 1 9 9 8 tine_ipb_1 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 1 532 00 44-59 Tine , Outer , L.H. 2 532 13 26-73 Cle vis Pin 3 532 00 65-54 Tine , Inner , L.H. 4 532 12 46-60 Retainer , Spr ing Zinc 5 532 13 27-27 Assemb ly , Hub and Plate, L.
26 1 532 40 37-07 Decal, Belt Guard 2 532 15 78-01 Decal, Control P anel 3 532 40 36-53 Decal, Logo 4 532 13 75-38 Decal, Control Tine 5 532 12 04-31 Decal, Hand Placement 6 532 10 21-80 Decal, Shift .
27 LIMITED W ARRANTY The Manuf acturer warrants to the original consumer purchaser that this product as manuf actured is free from de- f ects in mater ials and work man ship .
This product has been e xper tly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or par t replacement ma y be necessar y during the lif e of your unit.
デバイスPoulan PPCRT55の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan PPCRT55をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan PPCRT55の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan PPCRT55の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan PPCRT55で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan PPCRT55を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan PPCRT55の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan PPCRT55に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan PPCRT55デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
