PoulanメーカーPR621ESの使用説明書/サービス説明書
ページ先へ移動 of 28
OWNER'S MANUAL MODEL NUMBER: PR621ES SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 Safe Operation Practices for W alk-Behind Snow Throwers IMPORT ANT : This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . (d) Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner .
3 2. Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. 3. After striking a foreign object, stop the engine (motor), dis.
4 KNOW Y OUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Com- pare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
5 Setup Loose P arts Use the chart below to verify that all parts have been shipped. Procedure Description Qty . Use 1. No parts required – Unfold the handle. 2. Carriage bolts Flange nuts Washers Knob Chute Deflector 5 4 2 1 1 1 Install the discharge chute.
6 3. Filling the Engine with Oil ENGINE See engine manual. LUBRICA TION Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature. NOTE: Although multi-viscosity oils (5W30, 10W30 etc.
7 Operation NOTE: Determine the left and right sides of the machine from the normal operating position. • Gasoline is extremely flammable and explosive.
8 Starting the Engine 1. Push key in (Figure 10). 2. Move choke lever to left position (Figure 11). 3. Firmly push in the primer 3 times with your thumb, holding the primer in a for a second before releasing it each time (Figure 12). NOTE: Remove your glove when you push in the primer so that air cannot escape from the primer hole.
9 Engaging the Auger Blades T o engage the auger blades, hold the control bar against the handle (Figure 15). Disengaging the Auger Blades T o disengage the auger blades, release the control bar (Figure 16). The electrical cord can become damaged, causing a shock or fire.
10 Stopping the Engine T o stop the engine, pull key out (Figure 17). Adjusting the Discharge Chute and Chute Deflector T o adjust the discharge chute, move deflector chute handle left or right to desired position (Figure 18).
11 Operating Tips The auger blades can throw stones, toys, and other foreign objects and cause serious personal injury to the operator or to bystanders. • Keep the area to be cleared free of all objects that the auger blades could pick up and throw .
12 Adjusting the Control Cable Checking the Control Cable Release the control bar to remove the slack in the control cable (Figure 20). IMPORT ANT : The control cable must contain some slack when you disengage the control bar for the auger blades to stop properly .
13 Changing the Engine Oil Run the engine a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants. 4. Place an oil drain pan under the oil drain plug, remove the oil drain plug, and tip the snowthrower backward and drain the used oil in the oil drain pan (Figure 23).
14 Servicing the Spark Plug Use a NGK BPR6ES, Champion RN9YC, or BOSCH WR6DC spark plug or equivalent. 1. Stop the engine and wait for all moving parts to stop. 2. Rotate the discharge chute so that it faces forward. 3. Remove the discharge chute, the discharge chute handle by removing the three carriage bolts and flange nuts (Figure 27).
15 Replacing the Drive Belt If drive belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt. 1. Remove the drive side cover by removing the six screws as shown in (Figure 31). 2. Press down on front of idler arm to release the belt tension (Figure 31).
16 Storage Storing the Snowthrower Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.
17 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.
18 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) CHUTE AS SEMBL Y 9 10 11 1 2 2 3 4 4 4 5 6 19 19 8 20 7 4 4 6 15 21 19 15 16 17 18 SS ST -Chute asm_5 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
19 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) CHUTE AS SEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
20 KEY P ART NO . NO . QTY DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) HANDLE AS SEMBL Y 1 2 3 4 5 5 6 SS ST -Handle asm_1 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
21 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) AUGER ASSEMBL Y 9 9 10 10 1 2 3 4 5 6 7 7 8 11 11 11 12 12 13 13 4 5 5 6 1 1 14 SSST -Auger asm_1 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
22 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) SHROUD AS SEMBL Y 1 4 6 3 15 15 15 16 16 16 2 10 8 9 10 11 12 13 9 7 14 5 17 10 9 SS ST -Shroud asm_8 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
23 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) SHROUD AS SEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
24 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) FRAME AS SEMBL Y 1 2 3 4 4 5 7 6 11 10 6 8 3 9 SSST -Frame asm_3 12 12 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
25 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) FRAME AS SEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
26 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PR621ES (96182000400) DRIVE AS SEMBL Y 9 1 2 3 4 5 6 8 7 10 11 12 13 SSST -Drive asm_3 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
27 SERVICE NOTES.
28 LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in mate- rials and work man ship.
デバイスPoulan PR621ESの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan PR621ESをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan PR621ESの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan PR621ESの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan PR621ESで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan PR621ESを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan PR621ESの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan PR621ESに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan PR621ESデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
