Poulan Proメーカー403919の使用説明書/サービス説明書
ページ先へ移動 of 20
OWNER'S MANUAL MODEL NUMBER: B8527ES SNO W THR O WER Alwa ys W ear Eye Pr otection During Operation IMPOR T ANT MANU AL Do Not Thr ow A way W ARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. Fail ure to do so can result in serious injury .
2 IMPOR T ANT Safe Operation Practices f or W alk-Behind Snow Thro wers This snow thro wer is capable of amputating hands and f eet and throwing objects. F ailure to obser v e the f ollowing safety instructions could result in serious injur y . W ARNING: This snow thro wer is for use on sidewalks, drivewa ys and other ground le vel surfaces.
3 CONGRA TULA TIONS on your purchase of a ne w snow thrower . It has been designed, engineered and man u fac tured to give best possib le dependability and per fo r mance. Should you e xperience any problem y ou cannot easily remedy , please contact your nearest authorized ser vice center .
4 Read these instructions and this manual in its entirety before y ou attempt to assemble or operate y our new snow thr ower . Reading the entire manual will familiar - ize you with the unit, which will assist y ou in assembly , operation and maintenance of the product.
5 ASSEMBL Y / PRE-OPERA TION NO TE: The multi-wrench ma y be used for assemb ly of the chute rotator head to snow thro wer and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely .
6 ASSEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE RO T A TER HEAD (See Fig. 7) NO TE: The multi-wrench provided in y our par ts bag ma y be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening tow ard front of snow thrower .
7 OPERA TION KNO W Y OUR SNO W THR O WER READ THIS O WNER'S MANUAL AND ALL SAFETY R ULES BEFORE OPERA TING Y OUR SNOW THR OWER. Compare the illustrations with y our snow thrower to f amiliarize yourself with the location of v arious controls and adjustments.
8 OPERA TION ON / OFF switch - used to ST OP the engine . T raction drive control lever - used to engage po wer-pro- pelled f or ward or rev erse motion of snow thro wer . A ug er contr ol lever - used to engage auger motion (throw snow). Discharge chute contr ol lever - used to change the di- rec tion the snow is thrown.
9 The DIST ANCE that snow is thro wn is controlled by the position of the chute defl ector . Set the defl ector low to throw sno w a shor t distance; set the defl ector higher to throw sno w far ther . • T o change the defl ector position, loosen knob , mo ve de- fl ector to desired position and tighten knob securely .
10 OPERA TION T O THRO W SNO W (See Fig. 13) The auger rotation is controlled by the auger control le v er located on the right side handle. • Squeeze auger control lev er to handle to engage the auger and throw sno w . • Release the auger control le ver to stop thro wing snow .
11 T O ADJUST SKID PLA TES (See Fig. 16) NO TE: The wrench provided in y our par ts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scr aper bar and the ground surf ace.
12 OPERA TION COLD ST AR T - ELECTRIC ST ARTER 1. Inser t saf ety ignition key (pac ked separately in parts bag) into ignition slot until it clicks . DO NO T tur n the k ey . K eep the extr a safety ignition k ey in a saf e place. 2. Place ON / OFF switch in “ON” position.
13 GENERAL REC OM MEN DA TIONS The warranty on this sno w thrower does not co ver items that hav e been sub ject ed to operator abuse or negligence. T o receive full v alue from the warr anty , operator must maintain snow thro wer as in str uct ed in this manual.
14 MAINTENANCE A UGER GEAR CASE • The gear case was fi lled with lubr icant to the proper le vel at the f actor y . The only time the lubricant needs attention is if ser vice has been perf or med on the gear case. • If lubr icant is required, use only Rone x ED #1 grease.
15 CA UTION: Do not substitute . Use onl y original equip ment capscrew/shear bolts as sup plied with y our snow thro wer . 4. Connect spar k plug wire to spark plug. W ARNING: T o a void serious injury , before performing an y service or ad just ments: 1.
16 BEL T KEEPER IDLER ARM SQU ARE HOLE BOL T LOCK W ASHER TRA CTION DRIVE BEL T CLUTCHING IDLER ARM BRA CKET A UGER BEL T FLA T W ASHER A UGER PULLEY A UGER HOUSING FRAME ENGINE PULLEY LOCKW ASHER BOL T FIG.
17 SER VICE AND ADJUSTMENTS ST ORA GE Immediately prepare your unit f or storage at the end of the season or if the unit will not be used f or 30 days or more .
18 TR OUBLESHOO TING Does not start 1. Fuel shut-off valv e (if so 1. T ur n fuel shut-off v alve to OPEN position. equipped) in OFF position. 2. Saf ety ignition key 2. Inser t saf ety ignition ke y . is not inser ted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.
19 SER VICE NO TES.
LIMITED W ARRANTY The Manuf acturer warrants to the original consumer purchaser that this product as manuf actured is free from defects in materials and work man ship.
デバイスPoulan Pro 403919の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Poulan Pro 403919をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan Pro 403919の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan Pro 403919の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan Pro 403919で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan Pro 403919を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan Pro 403919の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan Pro 403919に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan Pro 403919デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。