Poulan Proメーカー416751の使用説明書/サービス説明書
ページ先へ移動 of 32
OWNER'S MANUAL MODEL NUMBER: PP13TEPH30 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 MAINTENANCE ..................................................... 14-15 SERVICE AND AD JUST MENTS ........................... 16-18 STORAGE ................................................................... 18 TROU BLE SHOOT ING ...................
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON.
5 AS SEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 AS SEMBL Y / PRE-OPERA TION INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.
7 AS SEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI (19-24.
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. FIG. 10 OPERA TION LH and RH turn triggers – used to steer the snow thrower . Drive speed control lever – used to select forward or reverse motion and speed of snow thrower .
10 TO CONTROL SNOW DISCHARGE (See Fig. 14) WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.
11 AUGER CONTROL LEVER FIG. 15 OPERA TION POWER STEERING OPERA TION (See Fig. 18) Steering triggers are used to assist in steering your snow throw- er . The triggers are located on the underside of each handle. When a trigger is squeezed, it disengages the drive wheel on that side of snow thrower and allows it to turn in that direction.
12 ADD GASOLINE (See Fig. 22) • Fill fuel tank to bottom of tank filler neck. Do not over - fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quan ti ties that can be used within 30 days to assure fuel freshness.
13 30 days or longer . Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty . Use fresh fuel next sea- son. See Storage In struc tions for ad di tion al information. Never use engine or car bu re tor cleaner products in the fuel tank or per ma nent damage may occur .
14 SNOW THROWER Always observe the safety rules when performing any main te nance. TIRES • Maintain proper air pressure in both tires (14–17 P .S.I.
15 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual).
16 WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact with plug.
17 1. REMOVE GASOLINE FROM FUEL T ANK - Drain gasoline from fuel tank into a suitable container , out- doors, away from fire or flame. Wipe up any spilled gasoline.
18 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
19 TROUBLESHOOTING Does not start 1. F uel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.
20 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) AUGER HOUSING / IMPELLER ASSEMBL Y 6 6 5 9 9 12 7 7 8 6 11 57 10 10 13 4 14 16 15 36 37 50 47 42 42 44 27 27 43 43 46 38 45 41 40 39 34 .
21 KEY P ART NO . NO. DESCRIPTION 4 191079 Pulley , Impeller 5 188909 Bearing Assembly , Flange 6 155377 Nut, Hex Flange 5/16-18 7 180355 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 72270505 Bolt, Carri.
22 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) CONTROL P ANEL / DISCHARGE CHUTE 3 32 32 2 2 1 1 6 19 2 26 34 21 35 33 36 28 27 25 20 29 31 37 30 16 18 17 10 14 3 13 15 9 11 12 7 5 6 8.
23 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) CONTROL P ANEL / DISCHARGE CHUTE KEY P ART NO . NO. DESCRIPTION 1 414280 Knob, Lever , Black 2 17501010 Screw #10-24 x 5/8 3 198475 Cont.
24 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) HANDLES .
25 KEY P ART NO . NO. DESCRIPTION 1 412682X479 Lever , Auger Control, RH 2 412681X479 Lever , T raction Drive Control, LH 5 169675 Retainer , Hairpin 6 17060408 Screw , Hex Head 1/4-20 x 3/4 7 412677 .
26 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) DRIVE 11 8 3 3 4 23 1 1 5 5 2 2 7 9 10 6 14 12 18 19 20 13 13 13 13 15 16 22 21.
27 KEY P ART NO . NO. DESCRIPTION 1 17490508 Screw 1/4-20 x 1/2 2 187794 Spacer , Axle 3 174697 Washer , Thrust 4 74780632 Screw , Cap, Hex Head 3/8-16 x 2 5 179830 Bearing, Axle 6 73930600 Nut, Hex, .
28 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) CHAS SIS / ENGINE / PULLEYS 30 29 31 31 44 49 50 51 52 5 44 45 58 6 19 17 10 21 22 23 2 1 4 6 42 8 9 12 13 15 27 26 25 24 18 7 20 14 10 .
29 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) CHAS SIS / ENGINE / PULLEYS KEY P ART NO . NO. DESCRIPTION 1 192873 Spring, Traction Idler 2 180522 Pulley, Idler (2-1/4) 3 - - - Engine.
30 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) WHEELS / DECALS 31 2 7 8 4 3 4 4 4 10 32 30 32 30 15 18 17 19 13 20 11 21 33 22 23 24 25 26 28 27 28 27 26 25 24 23 22 33 19 21 16 20 11.
31 REP AIR P ARTS SNOW THROWER - MODEL PP13TEPH30 (96198000901) WHEELS / DECALS KEY P ART NO . NO. DESCRIPTION 1 196752X421 Wheel Assembly , 16", with Power Steering, LH 2 155443 Pin, Klik 1/4 3 .
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship.
デバイスPoulan Pro 416751の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan Pro 416751をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan Pro 416751の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan Pro 416751の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan Pro 416751で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan Pro 416751を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan Pro 416751の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan Pro 416751に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan Pro 416751デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
