Poulan Proメーカー424549の使用説明書/サービス説明書
ページ先へ移動 of 40
OWNER'S MANUAL MODEL NUMBER: 961980025 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u fac - tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center .
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (1) POWER CORD (198563) (1) DISCHARGE CHUTE (3) RET AINER SPRINGS (169675) (1) TRACTION DRIVE CONTROL ROD (2) SHEAR BOL TS 1/4-20 x 1-3/4 (198636) (2) SP ACERS.
5 AS SEMBL Y / PRE-OPERA TION SPEED CON TROL ROD SPEED CONTROL BRACKET RET AINER SPRING SPEED CONTROL LEVER FIG. 2 TRACTION DRIVE CON TROL ROD DRIVE CONTROL BRACKET RET AINER SPRING TRACTION DRIVE CON TROL LEVER FIG. 4 TRACTION DRIVE CONTROL ROD PIVOT BRACKET RUBBER SLEEVE L OOP OPEN- ING DOWN FIG.
6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING Y OUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
8 OPERA TION Throttle/engine control - used to se lect either F AST or SL OW engine speed and to STOP the engine. T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow).
9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles.
10 OPERA TION USING THE CLEAN-OUT TOOL (See Fig. 15) In certain snow conditions, the discharge chute may be- come clogged with ice and snow . Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or in spect ing, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped.
11 OPERA TION TO ADJUST SKID PL A TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface.
12 OPERA TION COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in “FAST” position.
13 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
14 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease.
15 CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower . 4. Connect spark plug wire to spark plug. Replace safety ignition key . WARNING: T o avoid serious injury , before performing any service or ad just ments: 1.
16 SERVICE AND ADJUSTMENTS WARNING: Belt replacement requires separation of the snow thrower . While separating the auger housing from the frame assembly , it is important that an assistant stand in the operating po si tion and hold the snow thrower han dles.
17 SERVICE AND ADJUSTMENTS STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.
18 STORAGE CYLINDER 1. Remove spark plug. 2. P our one ounce (29 ml) of oil through spark plug hole into cylinder . 3. Pull recoil starter handle slowly a few times to dis trib ute oil. 4. Replace with new spark plug. OTHER • Remove safety ignition key; store it in a safe place.
19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position.
20 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
21 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
22 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P AR TS SNOW THROWER - - MODEL NO .
23 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P AR TS SNOW THROWER - - MODEL NO .
24 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
25 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
26 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
27 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
28 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P AR TS SNOW THROWER - - MODEL NO .
30 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
31 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
32 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
33 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
34 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
35 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) WHEELS KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
36 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
37 5 3 1 4 2 1 7 6 8 9 REP AIR P AR TS SNOW THROWER - - MODEL NO . 961980025 (96198002500) DECALS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
38 SERVICE NOTES.
39 SERVICE NOTES.
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship.
デバイスPoulan Pro 424549の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan Pro 424549をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan Pro 424549の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan Pro 424549の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan Pro 424549で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan Pro 424549を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan Pro 424549の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan Pro 424549に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan Pro 424549デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
