Poulan Proメーカー428496の使用説明書/サービス説明書
ページ先へ移動 of 40
OWNER'S MANUAL MODEL NUMBER: PP208E24 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 6. When cleaning, repairing or inspecting the snow thrower , stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (1) POWER CORD (198563) (1) DISCHARGE CHUTE (3) RET AINER SPRINGS (169675) (2) SHEAR BOL TS 1/4-20 x 1-3/4 (192090) (2) L OCKNUTS 1/4-20 (73800400) EXTRA SHEAR.
5 AS SEMBL Y / PRE-OPERA TION SPEED CON TROL ROD SPEED CONTROL BRACKET RET AINER SPRING SPEED CONTROL LEVER FIG. 2 SPEED CONTROL ROD HANDLE KNOB L OWER HANDLE PL ASTIC TIE UPPER HANDLE FIG. 1 INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower .
6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
8 OPERA TION Choke control - used for starting a cold engine. Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power -pro- pelled for ward or reverse motion of snow thrower .
9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles.
10 OPERA TION TO THROW SNOW (See Fig. 13) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow .
11 TO ADJUST SKID PL A TES (See Fig. 16) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface.
12 OPERA TION TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .
13 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
14 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual).
15 SERVICE AND ADJUSTMENTS WARNING: T o avoid serious injury , before performing any service or ad- just ments: 1. Be sure the on/off switch is in the OFF position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped.
16 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.
17 SERVICE AND ADJUSTMENTS NOTE: T o seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer . Tire sealant also prevents tire dry rot and cor ro sion. ENGINE See engine manual. CARBURETOR Y our carburetor is not adjustable.
18 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
19 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.
20 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
21 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
22 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
23 KEY P ART NO . NO. DESCRIPTION 1 2 3 4 4 3 01.11.001-A KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
24 KEY P ART NO . NO. DESCRIPTION 1 2 3 4 5 6 6 7 8 9 11 11 11 10 01.09.001-A NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
25 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
26 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
27 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
28 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
30 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
31 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
32 KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
33 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
34 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
35 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600) WHEELS KEY P ART NO .
36 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 01.14.009-A 1 1 422663 SAFETY IGNITION KEY REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600) BAG OF P ARTS NOTE: All component dimensions given in U.
37 KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
38 SERVICE NOTES.
39 SERVICE NOTES.
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship.
デバイスPoulan Pro 428496の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Poulan Pro 428496をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPoulan Pro 428496の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Poulan Pro 428496の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Poulan Pro 428496で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Poulan Pro 428496を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPoulan Pro 428496の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Poulan Pro 428496に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPoulan Pro 428496デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
